Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
Hello,
I'm using the rigado BMD350 in a new device with the legacy BMDware (AE firmware).
I'm have enabled the uart service and i'm debugging the transmission using the...
Hello,
I am trying to use the CLI example, but when I compile and upload it, LED1 does not blink and I do not get anything back on the serial port.
There is no error during...
Hi,
According to the data sheet, nrf52840 supports XIP mode on QSPI flash. Can we configure I2S(easyDMA) to load the tone from external flash with XIP address and play it...
I use a motion sensor interrupt and 4 buttons and one charge interrupt, all works well in product development, but after go into mass production, some pcs product( 1 or 2...
On the previous nRF51822 project the SWDIO pin could be used for nRESET.
The nRF52832 Product Specification and example code program nRESET to P0.21.
The Product Spec...
Hi,
One of my customers examine the feasibility of using nRF52832 as Peripheral only ,his mandatory request is Security because the product is an electronic lock.
Please...
I use nrf51822 to do bluetooth keyboard, I hope the function is: I want to change the IRK value of the bluetooth keyboard each time it is paired and bound,Anybody know how...
Hi can somebody help why nrf52840 doesnt be reseted when you press SW5(if boot/reset)? I have alredy with tried with few examples flashed on nrf52840 and in Segger IDE set...
Problem :
I have two I2C devices and would like to connect them both to nRF52840 DK on different I2C pins. According to datasheet nRF52840 has two I2C pins (P1.00, P0.22...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hi,
I am trying to build out a button pressing scheme for BSP on a custom device with 15 buttons operating on a BL652 Laird Module (underlying nRF52832). After modifying...
I'm working with the NRF9160 DK and have found the sample times for the ADC to be abnormally long. I am sampling three channels and seeing a total time for the ADC read of...
Hey guys, I am using 2 nRF52832 boards with a PCA10040. I program my boards with the BLE UART central and peripheral examples. I was wondering if it is possible to, and if...
Hello,
I used 3 nRF52-DKs to run the pb_remote and it ran well with the Mesh SDK v0.10.1. Then I created my own project and copied the code from the pb_remote client and...
Hi,
I'd like to test the sample udp_gps but SES throwes an error and a warning. The warning says: Path/udp_gps/prj.conf:36 warning: attempt to assign the value 'y' to the...
