Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I defined an integer value _ALIGN(4) uint8_t sixteen = 16 and assigned sixteen to a FDS record that is later assigned to the p_data of a custom characteristic. However, when...
I updated to v10.3.0 of the nrfjprog and mergehex tools and I've noticed that the behavior of the page erase command takes far less time when it gets to a certain region of...
Dear All,
I am trying to interface my nRF9160 sensor with the LIS3DH accelerometer.
What I have done so far are the following:
I am trying to use I2C_2
In my prj...
Hello Nordic Support,
I am using nRF9160-DK with the latest module firmware: 1.0.1, board version 0.8.3
I followed the instruction and it only works for tag v0.4.0, I...
Hi devzone!
I connected my flame detector sensor(szh-ek086) which sends data analog value to my nrf52840 DK.
To receive the analog value from sensor I used saadc module...
Hello, I'm trying to set up a series of remote scripts to test functionality on my hardware. The idea being that I can run a handler on the Nordic device and then control...
Hi,
is it possible to read/write the MX25R6435F external SPI NOR flash using Indirect Mode ( https://wiki.segger.com/Programming_External_SPI_Flashes) with Segger JLink...
Dear,
I am doing some range tests with the nRF52840 and saw that the RSSI value of the PCA10059 (USB dongle) can be more than 10dB lower than the one of the PCA10056 ...
Hello everyone, I am trying to implement a blocking wait using the app_timer.
To do this, I am starting a one-shot timer whose callback function sets an initially false...
Maximum current consumption for each of the pins in the respective modules of PWM, TWI-I2C, TWIM-I2C, TWIS-I2C, SAADC, UART, SPIM, TIMER, RADIO-2.4GHz under the operating...
Hi,
I'm trying to run the gps application off the master branch on the thingy91 and it dies like this:
It's built using the Nordic SES on windows.
Any ideas? ...
Hi all,
I am trying to connect to device with specific UUID. I am not sure what have I managed to do, below are some logs from NRF Log.
Did I connect properly?
I am...
Hello,
I am trying to run the mbdedtls example of random number generator shown here https://tls.mbed.org/kb/how-to/add-a-random-generator
I added MBEDTLS_CONFIG_FILE...
when i change the baud rate to 115200 my uart (Rx and TX) are giving me garbage out put.
so what do i need to change in my code(ble_app_uart example) when i have plan...
