Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Hello,
we are working on a BLE + Thread project, and it is currently based on NCS 2.6. We would like to update the SDK to a current one, and I see that there is a preview...
Hi,
I have added " config HW_STACK_PROTECTION" in KConfig file of the board.
Is there a way I can check during runtime if the Stack Protection is enabled? Is there any...
Hello
I am building a hardware that requires to use the nRF9160 together with the nRF52840, in order to add the 2.4GHz radio support to the system and also to be able to...
Hi,
Is it possible to run nRF5 SDK for Mesh examples on nRF Connect SDK for Bluetooth Mesh using nRF52840 Dev Board?
Examples are available on this github page.
https...
Hello,
I am trying to make GPIO P0.07 to high, in my nrf5340 Audio DK. Externally I am connecting an LED between P0.07 and GND. But it not showing any voltage between them...
I have the nRF Hw v1, and it seems like I did something wrong with a Fw:
nRF is recognizable by a computer as the COM3/4/5 device:
And it is accessible with the nRF...
Hi,
I want to know how to find the pack of nRF5 SDK.
Because the previous URL has expired. (http://developer.nordicsemi.com/nRF51_SDK/pieces/nRF_DeviceFamilyPack/ )
Hi Nordic
In the documentation of Zigbee sample of nrf Connect SDK, it said:
>>
Support for Zigbee R22 has been deprecated in nRF Connect SDK v2.8.0 and it will be...
Hi Community
Greetings, I bought nrf9151 DK module looking at the features, power consumption & size but the fact that NB IOT has a communication rate of 15mins once in...
Greetings,
We have a PCB with nrf52 and nrf91 on it.
We have nrf9160 firmware with MCUBoot. The chip boots into mcuboot dfu mode when a certain pin is set to high during...
Hello.
Thank you very much for releasing nRF Connect SDK v3.0.0-preview1.
I quickly tried the sample program, and while the build was successful, I encountered an issue...
Hi everybody
I'm trying to modify the Zephyr serial LTE modem example so that CMUX can be controlled using another communication interface, specifically I'm imagining...
Our application is designed to remain connected to the network - sending data every 10 minutes or so. We've customised the asset tracker v2 application, as this provides the...
NCS v2.6.0, devices based on nRF52840 (Fanstel BT840)
The project is a star network in which the Central is housed in a steel enclosure with a patch antenna perhaps 1cm...
I've been working on a peripheral wich accepts Just Works pairing requests and I'm completed at all points but the pairing itself. The device advertisises and connects successfully...
