Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hello,
I update ncs from v2.3.0 to v2.8.0 in matter windowcovering project.
my prj.conf file:
CONFIG_PM_DEVICE =y
CONFIG_PM_DEVICE_RUNTIME =y
CONFIG_USE_SEGGER_RTT...
Hi,
I'm developing a firmware based on Zigbee CLI sample. And I enabled DFU of app core and net core via serial with serial recovery mode.
Using SDK v2.4.2 and nRF5340...
Hi,
I am trying to integrate i2c code in peripheral_uart example from ncs 2.8.0.
I am following the steps as instructed in this exercise:
Exercise 1 - Nordic Developer...
I have nRF Connect for VS Code v2024.11.75 and am using SDK 2.6.1. In Lesson 3, Exercise 1 of the nRF Connect SDK Intermediate course in step 8 the instructions show to open...
I am a long time user of Doxygen and I am familiar with its format. I have been using Doxygen manually in my nRF9160 code and it is working fine. I am using DoxyWizard to...
Hi I am working on a project where I am trying to implement Bi-directional communication between 2 nrf modules connected to stm32f411ve dev boards. I am facing issue with...
nrf52840 with the official usb hid_generic routine transplant, the computer's 2.0 port hot swap probability is very small power-off restart, other ports are not tested out...
1. dts config file, I2C_SDA is configed GPIO P0.09/NFC1 , I2C_SCL is configed GPIO P0.10/NFC1, months ago, I'm using the old SDK, I also found that these pins configed as...
Hi Nordic team,
We need assistance in determining the appropriate GPS mode for our application: A-GPS or P-GPS? Though we believe A-GPS is more suitable for the use-case...
Hello,
My coleagues and I have been developing our application on the nRF5340 Audio DK for a while now and everything is working fine. Now we are at a stage where we want...
I am working on a custom development board with nRF5340 MCU. I have used two mics and integrated the LC3 codec library. I have assigned the following spaces in the prj.conf...
Hello,
I'm using a nRF5340 DK and ncs version 2.3.0.
What i try is, to use calls like
sdc_hci_cmd_vs_zephyr_read_chip_temp() that is available in header file sdc_hci_vs...
How can we retrieve all network devices RSSI/LQI value? Is there option to subscribe value for LQI ? We just want to showcase LQI/RSSI on server so user be aware if device...
Hi,
How can I retrieve the complete list of supported input and output clusters for all endpoints on a Zigbee end device? I'm currently able to access the On/Off cluster...
Hello,
I'm trying to use several USB CDC ACM instances with USB_DEVICE_STACK_NEXT. (nRF Connect SDK 2.8.0)
Is there a way to set the VID?
And is there a way to set different...
