Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hi y'all.
I've been developing in Zephyr NRF52840. My code is based in Central_HR_Coded (SDK 2.6.1, Toolchain 2.7.0). I had some issues with the bt_conn_disconnect function...
Hi, I'm new to this product and currently working on the Nordic Thingy:91X and have encountered some issues that I need help with. below is the details from the serial
monitor...
Hi,
I am developing an application with LTE-M connectivity to nRF Cloud. Our previous SIM apparently supported auto-APN provisioning, we did not have to set the APN, the...
Hello,
I bought brand new Thingy53, but Thingy53 turn off during deployment and can not connect to BLE, becuase it turns off. Please assist me if possible.
Hi,
I test my nrf54l15 module(disconnect every gpio with outside),the sleep current was 3uA,seens can't not achieve 0.6uA as the datasheet said.
The nrf54L15's markcode...
I am experimenting with sampling IQ at the payload in AoD mode. Are there any differences in the configuration of the receiver in AoA mode as seen in the direction finding...
Dear DevZone,
I believe I am quite familiar to this forum due to my ongoing Wi-Fi issues with SDK 2.6.1 To determine if a newer SDK version will resolve these problems,...
Hi,
I still try to configure Nordic-Zepyr build for a nrf5340, with a BLE stack and MCUBoot as the bootloader. The application will receive image updates over MQTT and store...
Hello everyone,
I'm having an issue with my nRF52840 Dongle. I can detect the device with nrfutil device list command, which shows:
> nrfutil device list DC1D9FD62EC5...
Hello Team,
I am trying to change the Lesson 9 Exercise 5 nrf5340_both_sol sample to use internal flash for FOTA. The code builds successfully. I have changed the pm_static...
Hi ,
I would like to use an external GPS active antenna on the nRF9151 EVB for testing (J2), does it disconnect the on board antenna GPS ? should I connect/disconnect any...
Trying to install NRF Command Line Tools. Platform is Linux 64bit x86 (distribution Ubuntu 22). I already have installed utilities by Segger, which may be the reason why NRF...
Question 1: I am using GPIO external interrupt. Does this interrupt belong to GPIOTE PORT EVENT by default? Question 2: How to configure low precision GPIOTE? Question 3:...
I use NCS2.5.0，and I noticed that there are two files(bluetooth.h and scan.h) can help to set scan parameters.Is there any difference betwen these two files?Can I call the...
