Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
hello :
We have a device that is ble master-slave and includes OTA function.
1. When the device adds a watchdog, the watchdog callback is triggered (wdt_event_handler...
I am new to IoT development, and am working with the Nordic Thingy:91, and nRF9160 development kit as a starting point for development. Is there a preferred operating system...
Hello,
im using nrf52840 with sd140 and sdk17.0.1
in my project i have implemented a libuarte communication that works well usually, but rarely, and usually after days...
Device Name : nRF52840-DK PCA10056
I have 4 questions listed below, the reason is Instead of creating multiple ticket/case we can follow up using the same ticket to avoid...
Hi! Thanks for reading this post. I'm having an issue creating a firmware package for our manufacturer. I'm using a nRF52832 with SDK version 15.3.0_59ac345. Whenever I merge...
I have a question about the baud rate of the UART. I have set the baud rate of the UART to 19200bps, but can it work without a problem even if there is a percentage difference...
Hello,
I have trouble to create a project on NRF9160 DK.
I follow all the steps on getting starting guide and i also check all the steps on getting starting assistant...
Hi Team,
Nrf52840 DK acting as central and we trying to connect our peripheral device, we observed below logs with total duration of around 300ms.
Is there any way limit...
Hi forum,
I am working on nrf52832 using sdk15.0.0. using project ble_app_beacon.
In this project I am setting tx_power 0dbm,4dbm,-4dbm and -8dbm.while setting this tx_power...
Hi, Nordic
nRF52 as GZP Device, nRF24 as GZP Host
I know if nRF52 is range of nRF24, the pair will be worked.
I want to know what is the distance.
And if I use unencrypt...
Hi everyone,
I work on an custom board with the nrf52840, the SDK 15.2.0, the SoftDevice 140 6.1.0 and FreeRTOS.
My problem is that during a BLE transfert of a lot of...
Can I develop a software with MESH network support (1MBPS) and 16 Central links (CODED_PHY)?
All my tries is unfortunaly. But I dont give up.
Just guide me please and...
Hi, I have 2 nRF52840 D K but suddenly both are not showing on my PC. I have checked my data cable which is working fine on mobile and transferring data. I have also checked...
Hello,
I am evaluating the possibility to use ESB protocol on nRF52840 development kit. As far as I understood, for HW limitations, the maximum number of pipes in a star...
Hi all.
I want to increase number of sending packets in TI. I searched for the answer and I found answer wasn't for v7.2.0.
please give me a solution for v7.2.0 sdk ....
