I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hi,
Kit : nrf5340
SDK: nrf connect SDK
I While testing the timeslot example in nrf samples part, I am getting the below error. Kindly tell me the procedure...
Hi!
I'm close to finishing a project where every type of messaging is done using simple BLE broadcasts (using my own frequency hopping and other features.)
However I...
Loss of comms between nRF24L01+ transmitter and receiver after successful data transfer.
One rf24 is configured as a PTX (sensor device) communicating in a simple point...
Hello,
I need to implement, say, 100 LPN + proxy and 1 friend + proxy, LPN are metering devices.
How can I send a value from a sensor to my phone without sending a request...
My project starts to grow and I would like to separate different parts of code into modules. Each module will present one .c file together with its .h file. In some .c files...
Would you be able to clarify why the Azure IoT hub is marked as experimental in NCS v1.5.0 on the menuconfig?
And is there any features missing or not verified etc?
And...
I am using S132 v7.0.1 on an NRF52832 to do a basic scan for BLE advertisements for 30 seconds (10 seconds on each primary advertising channel):
This works fine and as...
I am developing a custom board with NRF52832 and an audio DAC which outputs to a headphone jack. When the headphones are plugged in I can't program the board with my Segger...
Hi,
I have updated our SDK version from 15.0.0 to 15.3.0 for our custom board based on nrf52832
I wanted to rebuild the bootloader just in case it was needed. So i have...
Hi,
I referred and tested the File system Shell example on nRF52833-DK. In its source code, in file 'main.c', the function main() is empty/stubbed. Is there any way to customize...
Hello ALL,
I am trying to use MCU boot with my application. I am using NRF916DK and it has external Flash similar to NR52840DK board. Now when I am creating a partition...
Hi, I'm using BC805M module (nRF52805 SoC). I understand that the nRF52805 doesn't support BLE mesh. I would like to ask about the availability of using BLE (S112/S113) for...
Hi, I am in the process of evaluating nRF5340 to switch from STM32 device to nRF device as per my ex-colleague recommendation. I started looking at simple blinky example for...
I am using nRF connect v3.6.1 but the following error occur when i open the device in nrfconnect as follows:
Error :Unsupported device. The detected device could not be...
Hi,
I am using nrf Connect SDK v1.5.0
The immutable bootloader is located in nrf\samples\bootloader
My question is about the partition setting in the pm.yml.
This...
