Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hello,
I need to implement Find My Device for nRF52833.
From Sample I could find "samples/bluetooth/fast_pair/Locator Tag" example. I tried to go through it. but I could...
Hi,
We are using the nrf52833 for development.
The first version of the program can connect to the discovery service normally. But we need to add some new features. And...
Lesson 8 of "nRF Connect SDK Intermediate" DevAcademy course deals with Bootloaders. I've successfully done the exercise of updating firmware using the off-the-shelf mcuboot...
hi,i wanna read the imu sensor lsm6ds3 on board of nrf52840 based Xiao BLE Sense
so i used the code in samples /sensor/lsm6dsl
first i didn't know if i do have to create...
I'm trying to use the nrf_desktop application 100% standard, with NO changes to the codebase at all.
My initial assumption is, that once I flash the nrf52840dongle, it should...
I am working with ESB between 2 nRF5340DK's (w/ no need to be cross compatible w/ other devices) and with NCS v2.5.0. I am using ESB to wirelessly transmit data every 2ms...
I am a student currently studying BLE.
At present, I am working on a multi-connection setup where both the master and the slaves are using the nRF52832. Specifically, I...
Greetings starting from the 'ble aggregator' example I developed a BLE central on NRF52840 with NRF5 SDK 17.02, capable of managing multiple peripherals which, once connected...
I'm running SDK 2.8 and 2.8 Toolchain. I created the sysbuild.conf setting:
SB_CONFIG_BOOTLOADER_MCUBOOT=y
and put it in the application folder (per this support request...
Hello, I am relatively new to the nRF 5340 Audio DK. I recently ordered a singular nRF 5340 Audio DK board and my goal was for the board to take in input audio via the PDM...
Hi all,
I've been using the nRFConnect extension without any issues, successfully connecting to my nRF5340 board via JLink, flashing firmware, and receiving printed messages...
i get the following build error whenever i build for boards other than nrf
- CMake version: 3.21.0 -- Found Python3: C:/ncs/toolchains/b620d30767/opt/bin/python.exe (found...
Hello,
I encountered a compilation issue when using the app_timer function. The error message is: "'TickType_t' undeclared (first use in this function)". I believe the problem...
Hi,
I am trying to set the VDD pin to 3.0V instead of the current 1.8V (also changing the GPIO voltages to 3V). I've seen many questions related to that but no solution...
