the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hi
i want to create a bluetooth beacon which should get input in gatt(UUID,name,major,minor..then it should be advertise with the new UUID.
Iam configuring it with ibeacon...
Hi
I have tried to reproduce the 2.7µA current consumption stated in the datasheet. This webinar shows that the UDP sample reaches 2.7µA on the nRF9160 evaluation kit. However...
Hello Nordic! My question probably a simple one but I'm a novice so there's it. I'm looking for a way to get a GPIO port state that was at the moment of GPIOTE event triggering...
Dear Nordic Support
We have an existing Project that uses the nRF9160 SoC and builds with toolchain v2.4.4 and SDK v2.4.4.
The project basically runs with the nRF9160...
Hello,
My DK stop working as programmer suddenly.
the VDD power is normal with 2.9V and the V5.
Try already to power on with reset button hold.
blinking is not Consitency...
Hi Support Team
We meet an issue like the screenshot below when I program nRF52840 chip via the SES.
The SES version is v5.42a.
The J-link we used to program is...
hi:
asset_tracker_v2\src\modules\led_module.c
I only found the file that calls the LEDs, I didn't find the specific initialization and control code? Can you tell me how...
Hello everyone, a pleasure and very grateful to be able to write in this forum.
I am trying to program a Nordic BLE device so that it does not appear in the pairing list...
Hello, I am developing a board using the nRF52840 QFN48 and powering it using a 3.7V single cell LiPo battery. Since the battery voltage is stepped down to 3.3V via an external...
Hi.
I would like con build nrf Connect OT COAP Client and Server on a zephyr 4.0.99 / toolchain: zephyr 0.17.0
I have downloaded nrf sdk 2.9.99
running:
west build...
Testing the RADIO TEXT example on 52811.
1. 52811 is not a supported target - so I must select all targets then the unsupported dts (nrf52840/nrf52811)
2. I add a Build...
Dear Team,
Is it possible to run BIS and PAwR concurrently while using PAST for synchronization? I am using the nRF52840 DK and NCS 2.8.
I managed to start two periodic...
I am working wih \nrf5_sdk_17.1.0_ddde560\examples\802_15_4\wireless_uart\secure\first\
And I want to add app timer to start a peroid works.
unfortunately， this timer...
