nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hello, For my project I need to control 3 gpios pins. I already found difficult to find gpios that were not already used internally. I decided to use the gpio0 - 8,9,10 they...
My nRF Connect SDK extension in VS Code did an auto update this morning, and now my whole IDE is non-functional.
This is the error I get when I go to the Quick Setup
...
Hi,
I have made a custom board with BL5340PA module from Ezurio and i try to test simple bluetooth advertisement code but i have this error and not able to see my bluetooth...
Hello,
I am developing an LTE-M application on nRF9151, using offloaded sockets to modem, including DTLS.
Everything works great - can connect to network, and communicate...
Hi,
Our devices are running on NRF52833 with soft device version s140. We are facing an issue to do DFU in one particular device. Details mentioned below:
We are able...
Hello,
We run a Bluetooth Mesh network with about 1,000 nodes. Our master node (antenna) consists of:
· An MCU running Zephyr Mesh and keeping the CDB.
· An embedded...
Hi,
We are using the LC3 driver in our product.
We measured the current consumption with and without the LC3 driver.
When the LC3 driver is enabled, the current is 4...
Hi, I'm experiencing a significant performance drop when switching from the nRF9160 to the nRF9151DK.
I have a firmware that sends around 300 kBytes of data over UART in...
Hi, I recently upgraded my nRF Connect SDK to 3.1, and have migrated my code (which was originally based on the direction finding connectionless example) to 3.1 so that it...
Our Jenksing builds when using Nrf Connect v2.7.0, the --no-sysbuild option and CMakePresets worked just fine. When migrating to Nrf Connect v3.0.2 and using sysbuild, they...
I have some issues with the default response handling.
My Zigbee door sensor sends a message, and I reply with the following code:
```
if ( ! cmd_info -> disable_default_response...
I need to maintain and update firmware written with 15.3 SDK on an nRF52832 on Windows 11. What is the exact software and tools I need to do this. The latest Segger development...
Hello,
My use case is the exact same use case as this forum post . I'd like to run BLE and Radio Test sample on the nRF5340. The device would be in 2 modes:
- BLE
-...
Hello,
I try to figure out, how to correctly setup MCUboot for an nrf5340, so that:
Application is updatable
BT Stack is updatable
Firmware Updates are encrypted...
