nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I'm having a hard time replicating the config needed to be DFU compatible with a build from an earlier SDK version. Earlier version used only a non upgradeable MCUBoot with...
Hi,
I am working on the channel sounding procedure with the nrf54l15 dk's right now and I have an external antenna that I want to use to improve the connection. I plugged...
On nrf-sdk 3.0.1, we were running nrf54 (main app) with Zephyr's PPP modem for nrf91 SLM. Everything was working fine. After upgrading to nrf-sdk 3.1.0, I am now getting this...
Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
Dear Nordic Specialist,
I am currently testing the minimum connection interval at which BLE Channel Sounding can operate reliably. Specifically, I would like to achieve...
Hello,
I was wondering if anyone would happen to have sample code to activate the accelerometer in the Thingy 91X? If also possible, it would be very helpful to have the...
I'm trying to setup some code to emulate an NFC tag with an NDEF external record based on the NFC tag sample in NCS 2.6.0.
The hardware is a custom board based on the nRF52840...
Hello I am investigating the power consumption of the nRF9151-DK using PPK II. The measurement settings are as follows.
・Connect PPK II's VOUT and DK's P22 VDD_nRF. ・Connect...
I use nrf5340 audio DK, SDK v3.0.2, and added an iso.conf,
A lot of warnings were reported during compilation.
Are these conf not effective?
If I want these conf...
I'm interested in configuring a NR5340DK as an end device on a Zigbee network where the coordinator is a 3rd party device that uses legacy Zigbee. I'm fairly new to Zigbee...
Hello. I'm trying to call an interrupt service routine (ISR) using IRQ_DIRECT_CONNECT, but it is not working.
Here is the flow of my code:
So, it is expected to print...
Hello,
I am adding security feature for BLE in nrf52810 custom board. I am using v2.9.1 toolchain and 2.9.1 sdk files
PFA BLE related file as well as .conf file as well...
What is the quiescent current of the PM1300 when it is not in SHIP or hibernate mode, but when it is "alive" and configured and running off the VBAT terminal, ignoring any...
Hello, I’m working with a custom board using nRF7002 + nRF5340 + MX25R64 (SPI4) , and I’m trying to perform firmware updates over Wi-Fi using a firmware file hosted on an...
Good evening. We're running into an issue with using all 4 peripherals on the nRF9151. At the moment we are using the 9151DK.
The issue arises as soon as we enable spi1...
