Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi all,
I am having a ble 5 beacon broadcast on my nrf 52840 chips. I would like to know that if it is backward compatible so that ble 4 smartphone can receive the packet...
Hi,
Running the asset_tracker V1 i obtain a LTE connection and date time:
[00:00:19.338,226] [0m<inf> asset_tracker: DATE_TIME_OBTAINED_NTP
I want to convert it...
Hi
I am a new person for nrf5340, I got the NRF5340 PDK. I unbox and check that four buttons. It works fine. Then I compile the blinky code and upload it to the board using...
Hello Devzone,
For my project I am using NFC and I am using the writeable NDEF message project as an example.
Everything is working except I have found one issue.
...
Hi Nordic Team,
I have one doubt which I can not able to understand.
Actually in my code I'm scanning some ble devices also in main infinite loop I'm reading some sensor...
We're using the CMW500 to talk to the NRF9160, and it connects ok but then gives the message "RRC Connection Reestablished". We tried using the asset-tracker example, which...
Hi, I have made the custom board without 32.786kHZ (low frequency clock)
I am trying change it to
RC OSC
HFCLK
but i tried to make the changes but debug doesn't...
Hello
I'm using an NRF5282 and this thread :
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/simple-application-level-authentication
I try to implement...
Hello, gentleman!
We are developing our nRF52840-based application using nRF Connect SDK v1.4.2. I know there is a NCS v1.5.1 already available, we plan to switch to that...
Hi, I am trying to get start nRF5340 and projects. In NCS 1.5.0
i am following this link https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_nrf5340.html...
Hi,
I found that after a DFU my application is slower to start up by about 200ms. However when programmed initially (via a physical connection) its fine. Its only after...
I hope to send a message from two slave to one master using nRF52 through bluetooth.
I send a message from a slave to a master with ble_app_uart_c and ble_app_uart.
And...
I wanted to start creating my own programs outside of the SDK directory structure, but can't get the simple tutorial example to work. I've seen the issues with spaces in directory...
Using pc_ble_driver_py (version 0.15.0) to create a peripheral with a specific Device Name in characteristic 0x2A00 (Generic access service), the resulting device name is...
