Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Hello,
I have developed 10pcs of one prototype with the nrf9160 SiP.
I have some questions regarding some errors im having.
Regarding the SIM 1V8 driver VCC, for...
I'm trying to update the modem on Thingy:91 using nRF Connect Programmer v3.6.0
I get these errors
18:50:16.131
Application data folder: /home/tmh/.config/nrfconnect...
I'm working with a NimbeLink SkyWire Nano Dev kit, but I am hoping the question is simple enough that I can get some quick help here. I'm new to this side of things, so any...
I want to send data of different sizes from one board to another, using nRF52840. I have tried following the UART example, by using one board as Central and another Peripheral...
Hi Nordic,
I am trying to build something based on your BLE uart example for the two units for the connection from your SDK 17.0.2
one unit is running the BLE UART central...
Dear nordic,
I need a advise from your side. my custom board has two spi device both are working same line. one is SD card interface and other is sensor which works in DMA...
nrf9160-DK to NB-IOT service at vodafore UK
```
[00:00:00.322,479] [0m<inf> asset_tracker: Connecting to LTE network. [0m[00:00:00.329,193] [0m<inf> asset_tracker: This...
I know that we have actually some countries in Europe which don't support LTE-M, therefore we like to have a fallback.
Does there exist a fallback option to GSM or EGPRS...
Hi,
So I was having an error which caused my application to stall in the "do_stop_check" part of the nrf_drv_twi.c file, so I added a bit of code to check if I could figure...
We have a device with the following configuration:
nrf5_SDK_for_Mesh_v3.1.0
nRF5_SDK_15.2.0
s140_nrf52_6.1.0_softdevice
mesh_bootloader_gccarmemb_nrf52840_xxAA ...
Hi,
I'm trying to make a script in Python using the nRF52840 dongle, to make some BLE advertising.
I'm using:
- Python 3.7.2 (32 bit)
- pc_ble_driver_py library
...
Hi everyone,
I'm using ses IDE to debug via J-link on nRF52840 DK.
I'm debbuging CDC ACM example ( I haven't changed it ) but when I debug: ret = app_usbd_cdc_acm_write...
I am designing a PCB for the nRF52833 aQFN chip. To reduce the cost of the PCB I would like to fanout the inner row of the IC package on a single layer by using 3/3mil traces...
