Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi,
I am evaluating the nRF52840-DK, and wanted to know if the source code is available for the 'Sniffer' project as I can only find the hex file.
Thanks in advance.
I would like to use functions from the date_time and dk_buttons_and_leds libraries in an nRF91 application. I included the following lines in the application's prj.conf file...
Hi! I'm trying to understand from the documentation why the reset pin is unique.
What I mean by that is why is the reset pin different than assigning a GPIO to a button...
Hi
I am new to bluetooth. I have two Fanstel BT832x ( Nordic nRF52832 module with Skyworks SKY66112 power amplifier) Chips. How do iImake them talk to each other using AT...
Hello Nordic Support,
I am working on an application that logs data to SD card when disconnected from USB and appears as USB Mass Storage Class on host PC when connected...
Hi ,I use SDK 15.2 ,and example is examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay\pca10040. When I call sd_ble_gattc_primary_services_discover not...
Hi teams,
I am working on Mesh SDK 4.0.0.
I have several server nodes and single client node and all server models are publishing to All-nodes(0xFFFF).
All nodes published...
What exactly are the GPIOTE IN[n] registers?
Is the IN[n] register a function pointer of a function to call when the the input condition occurs on the associated pin? If...
Hi! I'm working on a custom board with the nRF52840 via an SWD connection, from a debug out on an nRF52840 DK.
The debugger fails to connect to one of my boards, even though...
Hi,
I have CSV file stored on an SD card (which I create via the nordic board). I want to send this via a GATT connection.
I have gotten a service with a notifiable characteristic...
Hello,
I have a Thingy91 pca20035 board (not the DK). So far, I have had success building my own modifications of the asset_tracker application by building it using SES...
I can see for the same device on Android nRFconnect that the serial number in advertising data can be seen as here -->
The same device at same time on my iphone X with...
I using nRF52832 with nRF SDK 16.0.
I tested the SPIS example in the SDK.
I want to change the SPI Clock frequency to 8Mhz and read max 255byte at once.
How to set...
Hi
i m using Bmm150 magnetometer sensor. i m trying to read x y z values. However, im not able to obtain the correct magnetometer values. I'm getting 0000 as values in all...
Hi, I'm developing custom board with nrf52832
The problem is that when saadc returns negative value, all values that saadc returns after are max possible values from config...
