I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
We have bought nrf52 832 development kit.
When we checking the kit in nrf52 utility than it detects the IC nrf52 840 .
Hence we have erased all the memory in the DK...
Hi everyone,
I am using the following files to configure uart for laser distance sensor.
Serial Library
I am able to write command to the Laser sensor and also the laser...
Hi,
As far as I understand from this page [https://openthread.io/platforms Host / 802.15.4 Controller section] it is possible to have Dongle running thread attached to PC...
Hi, everyone,
We develope project on nRF52832 Chip. It has one UART port and we need to make it working as RS485. For this purpose we connected to TX/RX pins the required...
I am trying to send hundreds bytes to peripheral, the best tool that I can find, is still nrfConnec. But the data only be typed one by one. Is there any way let it load a...
I am using a nrf52832 with SDK 15.2 and softdevice s132 v6.1
My peripharal should transmit an iBeacon to wake up an application on the smartphone and also transmit a connectable...
Hello,
For a new project I am using the Decawave module DWM1001. This module is equipped with an NRF52832. I have already used the nrf52832 for previous project and I face...
Hi there,
Is there a specific sequence needed to power-up the NRF52840?
Let me get into the details:
My design uses configuration #5 from the datasheet (see below...
Hi, I'm using the serial example from the nRF5 SDK for Mesh (version 2.2.0) and after running it for extended time with data being received from nodes every few seconds, it...
I have a small app_usbd demo which works fine on the nrf52 dongle, but not on the larger nrf52840-dk.
I am running SDK 15.0 with the errata fix mentioned on several other...
ATT MTU THROUGHTPUT EXAMPLE FOR nRF52810 on KEIL using S132 v5.1.0 PLEASE >>>>>>>>>>>>>
Tried this : https://devzone.nordicsemi.com/b/blog/posts/the-s132-v5-1-0-is-now...
Hi!
I am currently developing product containing Thread mesh and BLE peripheral service. I am using Thread SDK v2 in my software. My application has to support writing to...
Is there any NRF51822 DFU guide under following conditions:
a. NRF51822
b. SDK11.0.0
c. Dual Bank BLE DFU(\examples\dfu\bootloader\pca10028\dual_bank_ble_s130\)
I...
