Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi I am not sure on the nRF51422 chip the iBeacon function is fully supported, is it ?
I can make the examples working on it but on the Nordic site only on the nRF51822 chip...
Hello,
we are trying to avoid using code that triggers hardware issue #39 in the nrf51822, which appears to be fixed in chips whose build code is Hx0.
We would like...
Hi,
I'm currently developing a firmware running on nRF51-dongles (PCA10028). The dongle communicates with a PC application over UART. Everything is working fine except...
Hello we would like to use the Nordic chip to send wireless messages from a node to other nodes directly,without hubs. We wouldn't like to be limited to up to 8 nodes receiving...
Hello,
Setup: Android 4.4.2 (LG G2), nRF51822 peripherial.
I noticed that once in a while when trying to connect to my nRF51 based device it won't connect and what is...
softdevice 8.01,app is hts. ceilphone is HTC one. nrf tools.
add some functions display，adc, eg. use nrf tools HTM connect to the board, it's reboot every time when clip...
I'm using nrf51422, SoftDevice 310 and SDK 6.1.0, when i call sd_ppi_channel_enable_set, it causes SOFTDEVICE_NOT_ENABLED error, but softdevice was enabled earlier with SOFTDEVICE_HANDLER_INIT...
Dear all.
I have some test result on DFU feature. Please any comment on this issue.
test condition
Mater control panel (64-bit version)
nRFgo studio...
In my application, I had these lines.
nrf_gpiote_event_config(0, mPinDat, NRF_GPIOTE_POLARITY_LOTOHI);
nrf_gpiote_event_config(1, mPinDat, NRF_GPIOTE_POLARITY_HITOLO...
Hi,
On iOS, is there any way to download files right into the nRF Toolbox "User files" ?
This would be useful for DFU tests, to retrieve my binaries from the web.
For...
Hi everyone,
When I set the radio's transmit power, I can use "sd_ble_gap_tx_power_set" function. If I want to get the radio's transmit power, is there any function I can...
I am using NRF_GPIOTE->EVENTS_IN[0] and NRF_GPIOTE->EVENTS_IN[1] in my software. I had my own GPIOTE_IRQHandler working.
Today I am adding UART module into my source code...
