Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
Hi,
This is a request for all the users to post some details of sensors they are using along with Nordic chips. We will get familiar with 10 most popular sensors that are...
I am trying to build PCA10040 examples but I am getting the following error:
make genhex
Preparing: .hex
/home/me/nrf52/gcc/gcc-arm-none-eabi-4_9-2015q1/bin/arm-none...
Hi guys
I am planning to develop a beacon app, but I am not sure what would be the minimum scanning interval in order to keep the phone's battery drain on a fairly good...
Hi, I use the following.
Raspberry Pi 3 (RPi3 with Raspbian Jessie 4.4) as a router,
RPi3 is connected to a Wi-Fi router to access the Internet by using the built...
Hi, there! nRf Toolbox drove me crazy!! can anyone help me?
I flash "s130_nrf51_2.0.0_softdevice.hex" to the pca10028 board.
I compile the bootloader example "nRF5_SDK_11...
Hi,
I'am having an issue with UART using app_uart_fifo.c (SDK 0.9.2). At times I get communication error (usually at attaching and detaching uart connector) and my error...
Hi.
I'm little worried about our bt sensor power consumption.
We are using twi/i2c to communicate with sensors periodically. We are using app timer to trigger these...
I have a custom board that doesn't use the external 32Khz crystal. The engineer that designed it chose to use P0.0 as UART RX. (I know, poor choice.) I have set up a custom_board...
I am using SDK_11 s130. I see APP_ERROR_CHECK(err_code) being used throughout the SDK examples. When err_code is any value other than NRF_SUCCESS, the nRF51-dk board will...
Previously, I was able to program ble_app_uart using SDK_11 s130 into nRF51-dk. Now, I would like to program ble_app_uart into Adafruit Bluefruit LE friend board. www.adafruit...
I have been following the advertising tutorial and decided to start my own application using nordics git repo as a reference. After a few debug sessions I found that I needed...
I am trying to probe sysclk signal on one of the unused GPIO pins on a nRF52 board. I modified the ble_app_template example provided in SDK 11.0.0 and added a sysclk function...
I am trying to connect nRF52 with 7120 and create a NFC card reader , is this a solution and power efficient solution .
I will interface through I2C , is there a example...
I am using the sdk version 11 and arm-none-eabi-gcc version 5.4 on linux mint to compile the blinky test application. I have pointed the Makefile-posix at the location of...