Hello everyone, currently I am writing a program to read the SCD41(I2C) sensor and then use BLE to transmit information. With a separate program in twi_sensor, I see that...
Hi All,
I was evaluating the throughput of NRF5340 using the DK. I would like to set the transmission power under 0 dBm of the peripheral device.
However, i was unable...
Hi, We are currently developing a embedded system with S130 where some parts that are performance critical. Timeslot API is in use.
The assert 0x0000f764 gets called ~15s...
I am working on an application for an LE Audio Broadcast sink on an nrf5340 Audio DK. I am using code from the nrf5340 Audio application (v2.6.0) for the le audio parts. I...
Hi, I have been testing the current consumption for nRF54L15-PDK (0.2.1) in System Off mode. The current is measured over the jumper named "CURRENT MEASURE" on the board....
Hi everyone.
I am looking for a main microcontroller that can communicate with nRF24L01+ 2.4GHz RF transceiver over ESB(Enhanced ShockBurst). And I found the nRF24LU1+ on...
Hello Nordic Official! I am currently doing the PCB design of NRF52840 based on your datasheet, but I have some questions.
The manual I refer to is this: [ https://infocenter...
Hi All,
I was evaluating the throughput of NRF5340 using the DK. I would like to set the transmission power under 0 dBm of the peripheral device.
However, i was unable...
Hi, We are currently developing a embedded system with S130 where some parts that are performance critical. Timeslot API is in use.
The assert 0x0000f764 gets called ~15s...
I'm using the NCS 2.5.2 sdk and nrf 5340 with 7002, and I want to do BLE OTA DFU using external flash.
I've found this guide Add DFU support to your application - Software...
Hi,
We are working on the nRF52833 in one of our Gateway applications. We want to keep our Gateway in deep sleep (System OFF) mode if it is not configured or On-boarded...
MY BUILD HAS THE FOLLOWING ERROR LOGS PRINTED IN THE CONSOLE
Executing task: nRF Connect: Build [pristine]: fund_less2_exer1/build (active) Building fund_less2_exer1...
Hello everyone,
I'm searching for examples or documentation on implementing UART XMODEM on my nRF52840. Could anyone assist me with this?
Thanks
Cedric
TRANSLATE...
Hi,
I am trying to install mcumgr using the following command on my Laptop which is running Linux Ubuntu 20.04.6 LTS.
"go get github.com/apache/mynewt-mcumgr-cli/mcumgr...
We're developing an LwM2M application based on the lwm2m client sample with the goal of sending data to ThingsBoard as our main telemetry platform.
The Application in based...
I have a BLE peripheral project that is based on NCS 2.5.0 using the typical flags for firmware update:
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU=y CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU_SPEEDUP...
Hi, when I use other modules (like NRF_LOG ecc) no problem, when i use UART or UARTE the script is ok but i can't see anything on PuTTY terminal. In my case, a LED should...
Hello, we are looking for answers to a few questions.
Our questions:
1)Will it be enough to change the resistor value on the VSET2 pin to obtain 3.1V on the VOUT2 pin...
I have a custom PCBA with which has the flow of:
- Boot
- Advertise some temperature data read from TWI with a 5 second timeout using `ble_adv_fast_timeout`.
- I then...
I am using the Android nrf connect app to connect to NRF5340-DK after mesh provisioning.
android pixel 7
nrf connect 4.28.0
If Android nrf connect uses 'auto connect...
Hi,
I am using nrf52840, nrf SDK16.0. we have created hex file using embuild. whenever hard fault occurs, we are storing had fault stack details in non-initialized memory...
I am working on an application for an LE Audio Broadcast sink on an nrf5340 Audio DK. I am using code from the nrf5340 Audio application (v2.6.0) for the le audio parts. I...