Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hey Guys，
Who can tell me what are the differences between the timer0, timer1 and timer2?
And if I want to set up timer interrupt in timer mode, the interrupt will be...
Hi everyone,
I took the example Ble_app_uart and I modified the Nus service for send data in Indicate mode.
With MCP I discover service and enable service (0x02->indicate...
Hi, every one,
In my application , we need to bond my device with host , and then our application will go to deep sleep by calling sd_power_system_off. When I wake up my...
Hi,
I have made some customs pcbs, the main one use the PCA10004 reference design and the small boards use PCA10000. I can get 25 meters on LOS (I think it can go far way...
Hello
Until recently I have been using a JLink EDU to program and test nRF51xx devices from Keil 5.14.
I recently bought a Ulink2 and would like to do the same but have...
Silly question, but I haven't gotten into a good rhythm with the debugger. Every time I try to use the debugger when a soft device is programmed, I can't seem to ever hit...
I'm trying to port the Dual Bank BLE DFU Bootloader to a custom board that we have. The only modification I have made in the bootloader was that I changed it so the internal...
I'm working in a project & I want to use the PWM application provided by the SDK with the bluetooth module, I want to control the LEDs light intensity using the PWM, the PWM...
I'm having difficulty with using PWM library with softdevice. The app_pwm_init function returns
NRF_SUCCESS but call to app_pwm_enable does not generate an output.
...
Hello,
Is that possible to connect to a device that is not advertising ? (a kind of wifi not send SSID)
In my case I know what mac address to connect so it's useless...
The critical section code in app_util_platform is controlled by the symbol SOFTDEVICE_PRESENT. Do I have to set it up in the project or is there something else that controls...
Hi,
My problem is next. I want to use some of examples for nrf51822 on costum board but code stuck at sd_softdevice_enable(). As I cant see where is this function defined...
My computer (Windows 7) cannot find any driver software for the nRF24E1, the dongle PCB in the nRF24Z1 development kit. Where can I find the software?
[edited 7/16] It...
The nRFgo Studio showed "No device detected" when the nRF51-DK board was plugged to the USB port. And the Recover button was greyed.
When the board was plugged in, nRFgo...
Hi,
I want to get a message to know if the S120 center have had get the adv packs.
Is there a way to make a scan respond ack payload pack from the S120 center?
