Hi,
I'm using the nRF52833 to develop a BLE beacon and built a Bluetooth gateway for my application.
Application Requirements:
The beacon should advertise using...
Hello,
I want to perform some antenna measurements and compare the rf performance of my custom PCB with an nrf9160 SiP with the nrf9160 dk.
To perform some antenna measurements...
Hello - I have the exact same question as proposed in this thread - I am wondering if there has been any change in the 3 last years since it was posted.
In a nutshell, we...
Hi I want to build a multi role BLE device.
As a peripheral it shall stream ADC data with arounf 20 kbytes per second.
As Central it shall receive adv_nonconn_ind packets...
Hello everyone,
I have an nRF5340 microcontroller (NORA B106 module), and I want to connect a square wave signal to one of its pins to read its frequency or count the number...
Hi,
Hope you are doing well.
I would like to use eSIM on nRF9151-DK board and an eSIM has been assembled in the board. However, eSIM is not detected.
According to...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
Hello, kindly any one tell me how to run a beacon code in nordic Ev kit . I've been trying to make it work . What type of changes i need to do in the code .
Hi,
I want to migrate my firmware from nRF51422 and softdevice S310 to nRF52 and softdevice S332.
Please share migrating step if anyone knows.
For nRF52 and Stack S332...
Hi!
I have an application that was originally developed for the QFAA using the S310 softdevice (v1.0). During subsequent development, we ran out of RAM memory, so we got...
I am trying to figure out what is the best way to implement a TWI Slave functionality on the Nordic chips. The HW seems only to support the TWI Master.
Is the only way to...
I have a nRF51822-EK Evaluation Kit (PCA10001) that I am trying to run example code for OTA DFU on as detailed in the tutorial here:
devzone.nordicsemi.com/.../
I have...
Hi,
I am trying to fade out 5 LEDs over the course of 500ms simultaneously. I am using soft device s110 but am happy to pause everything for the half a second while the...
[Bug Report] Possible bug in nRF52832 engineering release B.
When LF XTAL oscillator is started, no event is generated.
NRF_CLOCK->LFCLKSRC = CLOCK_LFCLKSRC_SRC_Xtal;...
I've created a custom service for a demonstration. I can view the see the device in Master Control Panel and view notifications and write to a characteristic that is writeable...
Hello,
I have a question about RAM usage. If i use chip with 16kB RAM, and if i use s130 (which uses 10kB RAM) and bootloader (which uses 4kB of ram) i only get left with...
hi, i am getting start nrf 51822 BEL with ble_app_uart
as a first step, i just compile the one of the BLE example 'ble_app_urat" which is located in 'C:\Keil_v5\ARM\Device...
I have a project that uses the nRF51822_xxAA chip with a pull-up button connected to pin 9. Using a meter, I have verified that the pin drops low (0 V) when the button is...
Hi,
I'm reading temperature and humidity from 2 sensors in my system
At some point in time during a quick and dirt check the system has been proven working fine and...
HI:
everyone!
How to make the matching and binding equipment information would be stored permanently, even after the OTA upgrade is still in;I made with examples of the...
Greetings, I tried to modify the parameter "len" to anything over 1 (byte), but it just doesn't work.
As long as it's over 1 byte, the API crashes my program. err_code shown...
