Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I have flashed the Blinky sample onto an nRF52840DK.
The power consumption is extremely high.
I am using an PPKII to in source mode. It is connected to the External Supply...
I am using nRF Cloud to update firmware on nRF9160 based products in the field. They are connected via LTE Cat-M on Telstra in Australia. The problem is that the download...
I need help with this issue. I'm updating the code from SDK 2.4.2 to SDK 2.9.2. I had change the device tree to HWM2 and I'm using sysbuild.
The build log is showing this...
SDK: 3.0, nRF54L15
I have modified the clusters using ZAP tool (west zap-gui). When I tried to built, I get the below error:
1. I used Matter door lock sample and the...
Please refer to the image below:(If you cannot see the image, link here: postimg.org/.../)
I'm not entirely sure what this pin does, does it output reference voltage...
Why can't I breakpoint or step blinky, using kiel MDK lite?
Comment --- I suggest Nordic do videos or provide exact steps for how to setup-run the base example (like Blinky...
I've been having a very difficult time debugging this issue. I've modified the bootloader_secure example and have it working on the dev kit using the 330 Softdevice. It works...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Hi Nordic,
My application does the following:
Timer 2 takes care of controlling a shift register (CLK and DATA)
Timer 1 takes care of polling data from sensor...
Hi!
I am in the process of upgrading a quite large project from SDK 8.1 to SDK 12.2. It uses the nRF52 DK, PCA10028. I still use the toolchain I stated with, including...
Following this tutorial , but for pca10028 , softdevice s130 instead. I'm on Linux.
Under "Running", when I press Ctrl + F5 , I get the error s130_nrf51_2.0.1_softdevice...
Hi,
I try to modifie ble_multilink example et send more than one data,
here is my main code code :
static uint8_t test[4] = {0x41, 0x42, 0x43, 0x44};
static...
Hello,
SPIS is adding a 350uA from 80uA baseline running current. I would like some tips and advise on improving this. Thanks!!!
The baseline operation consists of:...
I am using eclipse as IDE , but when i build ble_app_hrs example it's getting an error ../../../../../../components/ble/ble_advertising/ble_advertising.c:195: undefined reference...
I have a 32u4 Feather but don't get the right support from Adafruit to create my own Profile. I have downloaded Nordic's android app and can see all the characteristics on...
Hi.
I'm trying to enable and disable softdevice repeatedely.
In my code, softdevice is firstly enabled then advertising properly.
After some seconds, softdevice is disabled...
Hi,
I used the ble_peripheral and ble_central example and I send messages from one to the other.
Know I need to do the same with multilink.
I managed to connect ble_multilink_central...
hi dear Engineers!
the questions is it possible to use RX RF reciever to estimate the average BW RF signal input power like I do it in Semtech 433/868 RF SoC to make desicion...
hi, all
my nrf52832 can not run good when download the program into the flash, and can not run good in debug session mode without breakpoint ， but if I add one breakpoint...
