what can be the starting Point for Bachelor Thesis involving BLE 5.0 devices to be deploy in mesh Network. How the challanges in the Thesis can be address and set as a Goal...
Note: This is related to the following issues:
- https://devzone.nordicsemi.com/f/nordic-q-a/63255/nrf9160-getting-stuck-after-cell-change
- https://devzone.nordicsemi...
Hi, I am Product Manager working for Medical Device Manufacturing company based out of Ireland.
we are in search for a development house / developer who will support us...
I have so many versions of this topic that I now am certain that most of the answers provided are wrong. Since you cannot have so many ways of connecting an external nrf device...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a vendor specific characteristic for the battery voltage in my device, expressed as an actual voltage rather than a percentage. Values are 0.000V to about 4.300V and...
HI,all!
I recently using pstorage to store data
and the pstorage_store(); funtion always returns NRF_SUCCESS, but never triggle the cb_handler, is that normal?
by...
[environment: s110_nRF51822_7.0.0 + SDK nrf51_sdk_v6_0_0_43681 + PCA10000(QF AAG0)]
I failed to get pstorage working in my own code, then I picked up the sample code from...
My NRF51822 die. When connected, keil can't download or erase flash. But it can be found by SW port when I just power on, then it almost be unavailable at the same time. ...
Hi,
I am trying to use the RX interrupt on the PCA10001 board, using UART0 for wired communication and S110 (s110_nrf51822_5.2.1) for Bluetooth LE communication at the...
Hi, i'm trying to communicate between a msp-430f5529 (spi master) and a nrf51822 (spi slave). I have configured the MISO, MOSI, CS and SCLK of the nrf. I use the spi_slave_example...
Hi there,
I'm currently facing the problem, that an example as simple as
volatile float sum;
extern "C" int _start()
{
float a = 1.0;
double d = 2.2;
sum = a ...
I have a nRF51822 mkit board which I would like to use as a BLE peripheral to connect to my linux computer with BlueZ. I would like to be able to have a simple GATT connection...
Hi,
I'm trying to get a SPI based peripheral going without much luck.
One thing I noticed, in the debugger, is that on my implementation the field spi_base_address->POWER...
Hi,
I'm getting problems on the pca10001 uart example. I get the "Start:" string on the terminal but it can't echo what I type on the keyboard. Another thing is that I...
The nrf51 powerdown examples
github.com/.../nrf51-powerdown-examples.git
Are these power down examples are helpful. They clearly indicate how to power on the nrf51822...
I have a custom board using the nRF51822 as a peripheral with the S110 SoftDevice. The centrals are mobile apps, both Android and iOS. The device spends a lot of time in a...
Hi
I'm trying to run uart example on nrf6310.
I followed following link.
devzone.nordicsemi.com/.../
and I defined ENABLE_LOOPBACK_TEST.
it was resulted in blinking...
I am using sd 7.0.0, I have a simple bootloader implementation that follows the bootloader sample code pretty closely. When I jump to my application from the bootloader and...
