Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
Hi All,
I would like to design a wireless system using nRF51822 with an effective range >100m LoS and 5m under water.The system is used as a ON-OFF control device powered...
I am trying to run an Arduino sketch using the RedBearLab nRF51822. The sketch is designed to transfer data to and from a microprocessor and an Android device via bluetooth...
I'm currently want to use the NVM with ble device, when I tried to send values from the mobile app to be stored to the NVM, it doesn't work, I guessed that the problem that...
I want to write a device ID to the UICR registers at the same time as I flash the app code. I don't use Keil or that nrfproj.exe thing, I'm on a Mac. I have these targets...
Dear Nordic team,
I have the nRF51-Dongle and would like to use it with master control panel.
I did everything like already recommended in this tutorial .
The problem...
SDK 9.0
nRF51
PCA10028
I want use nRF51 gazell function one host multi device. Reference example code "gzp_dynamic_pairing",host and device can auto pairing .
But in host...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hey Guys，
Who can tell me what are the differences between the timer0, timer1 and timer2?
And if I want to set up timer interrupt in timer mode, the interrupt will be...
Hi everyone,
I took the example Ble_app_uart and I modified the Nus service for send data in Indicate mode.
With MCP I discover service and enable service (0x02->indicate...
Hi, every one,
In my application , we need to bond my device with host , and then our application will go to deep sleep by calling sd_power_system_off. When I wake up my...
Hi,
I have made some customs pcbs, the main one use the PCA10004 reference design and the small boards use PCA10000. I can get 25 meters on LOS (I think it can go far way...
Hello
Until recently I have been using a JLink EDU to program and test nRF51xx devices from Keil 5.14.
I recently bought a Ulink2 and would like to do the same but have...
Silly question, but I haven't gotten into a good rhythm with the debugger. Every time I try to use the debugger when a soft device is programmed, I can't seem to ever hit...
I'm trying to port the Dual Bank BLE DFU Bootloader to a custom board that we have. The only modification I have made in the bootloader was that I changed it so the internal...
