I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi All,
I'm using Nordic UART App to write 'A' to TX characterstic and then i expect some action after that as per my code on BLE nordic device, which is happening.
But...
I'm using the attached proximity_setup.xml ( proximity_setup.xml ).
I'm trying to use the Battery Service to send Battery Level notification.
I added the following code...
Hi,
I have just received a nRF52832 Preview DK and I am trying to set it up according to the description in the nRF52 Series - Get Started section.
I have connected the...
Hi All,
I am using nRF51422DK with SDK 10 and trying to communicate with an external peripheral over UART at every timer interrupt.
I have modified the ble_app_hrs example...
Hi All -
Is there anyone successfully able to autoconnect with nrf51822 with a phone/pc/tablet? I have been trying it for the past week and couldn't get my nRF51822 autoconnect...
I successfully turned off bluetooth radio using NRF_RADIO->TASKS_DISABLE = 1 when i do advertise_start(); after certain delay i coudnt connect back for data transfer
Based on nRF51822\Board\pca10001\ble\ble_app_hrs example,
How nRF51822 detect ADC input? Which ADC pin?
Configuration code:
NRF_ADC->CONFIG = (ADC_CONFIG_RES_8bit <<...
Hi, I'm having a problem with calling pstorage_register(); The first I call pstorage_register() is just fine, but the second I call return the nrf_invalid_param.Here is the...
Hi......
the board advertising correct,and it work normal (connect,send and receive data),bug it's name can not display in app scan menu. the definition is "liu",but displaying...
Hello,
I have been trying to use the nRF52 preview DK board as a master device with another chip as its slave device. Now I know that to read or write the function used...
The statements
NRF_PPI->TASKS_CHG[n].DIS = 1, and
sd_ppi_group_task_disable(n)
cause a hardfault when NRF_UICR->CLENR0 is set to the start of the application code, but...
I'm working on a battery powered system which needs to keep track of an absolute time stamp. So I need the RTC module and some kind of energy saving mode. As the RTC is not...
8.0, multilink example, peripheral, s110 softdevice.
By walking through sections of codes and doing some research, I reckon if a connection were being established after...
