void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
So for this what I am trying to do is-
result = ((float_t)0x3F4040A3); NRF_LOG_INFO("My float number" NRF_LOG_FLOAT_MARKER "\r\n", NRF_LOG_FLOAT(result));
But this is...
Hi
I have a strange phenomenon when using ANT proximity function.
Configuration: nRF52840, SDK15.2.0, softdevice S340 v6.1.1
The following initialization function of...
I've been using the USB HID Composite example along with the advice from this thread https://devzone.nordicsemi.com/f/nordic-q-a/38271/writing-words-to-usb-composite-keyboard...
Good day
I'm trying to run the ANT IO demo using two nRF52840 DKs. In order to do that I am trying to migrate the example from softdevice s212 to s340. I am currently using...
hi,
i want to connect 18 peripherals to a central. if iam changing NRF_SDH_BLE_CENTRAL_LINK_COUNT and NRF_SDH_BLE_TOTAL_LINK_COUNT more than 8, all peripherals stop pairing...
Hi,
usbd_cdc_acm project implemented UART over usb, which is great. However it cannot send bytes from PC to DK board, only DK board back to PC.
In order to implement sending...
I use the SPIM to access a nand flash memory device. There are times, when I need to "free" the SPI bus allocated by the nRF52840, so that another CPU can access the memory...
I have been closely following this thread ( https://devzone.nordicsemi.com/f/nordic-q-a/52689/nrf9160-lte-sensor-gateway-on-thingy-91/217018 ) to provide support for the LTE...
Hello all,
I am using the NRF52810 board with SDK 14.2
I wanted to convert pca10040 to pca10040e file of buttonless dfu and secure bootloader .
I have gone through this...
Hi, I can read data with my laptop BLE as below.
Could anyone tell me where can I find the data layout doc? I want to figure out the data layout and dimension.
Thanks...
I've been having several issues with the nRF52840 so far:
Issue 1:
When trying to flash an nRF52840 with NCP firmware using a Segger JLink, I connected the SWDIO and...
Hi all,
I noticed an issue on the last release of the NRF Connect mobile app at least on Adroid devices.
It seems that every time I am trying to make a secure DFU (buttonless...
Hey everyone!
How often does PM write into FDS? On each connection? Or on each new bonding? PM has some kind of peer ranking so I suppose that it needs to write on each...
Hi Nordic Forum! I'm currently developing a CLI controlled BLE scanner using the nRF52840 Dongle. Essentially I brought over the CLI example and adapted it to the a central...
