Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Scenario: I want to use an Arduino shield with the nRF51 DK. When attached to an Arduino, the Arduino's barrel jack is plugged into a 12V power supply. The shield takes advantage...
I am working on a ble project using the nRF51422 and IAR. I can load the code onto the board from IAR and it works as expected, but I run into errors when I run the code with...
Hello there,
I use the MasterEmulator.dll with LabView and the nRF51 Dongle and everything works fine in the past.
Now I had to change something in my LabView software...
Hi all,
recently I tried sd8.0 and i used the example "ble_app_hrs".
the strange thing is in my phone i can see device advertising but cannot connect to it successfully...
I tried to use this example with a nRF51422 and the board of N5 Starter Kit of Dynastream. I adjust all to make it works fine: custom_board and so on.. And I used the Soft...
From SDK 7.2, we have the following definitions:
components\drivers_nrf\pstorage\config\pstorage_platform.h
typedef uint16_t pstorage_size_t; /** Size of length and...
There was something in the webcast yesterday about a Nordic nRF52 roadshow/tech tour/worldwide series of events.
I hunted around the nordicsemi site but didn't find anything...
hi,
i am working on ble project where i am trying to develop a project with master(mobile phone)-bridge(acting as master and slave,nrf board)-slave(nrf board) .i use the...
Hi,
I would like to save the most energy when going to sleep mode. In particular, I want to turn off all modules except the RTC timer.
So, after shutting down the radio...
Hi,
How could i implement Just work pairing method in my "ble central and peripheral" example. I modified project to suit my need, and everything works fine, untill i try...
I am working on a ble project ,'ble_central_and_peripheral",s130.In this project the device acts as master and slave. It connects to the slave only if the address is predefined...
I may be missing something. I am trying to generate a square wave from a GPIO pin in a BLE application (SoftDevice 8.0). I tried libraries (nrf_pwm.c and nrf_pwm.h) in this...
Why does the nRF52 only have +4dB output when most competitor chips are atleast +6dB (some up to +10dB). I understand that the RX has been improved by 3dB for a better overall...
