Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hey Guys，
Who can tell me what are the differences between the timer0, timer1 and timer2?
And if I want to set up timer interrupt in timer mode, the interrupt will be...
Hi everyone,
I took the example Ble_app_uart and I modified the Nus service for send data in Indicate mode.
With MCP I discover service and enable service (0x02->indicate...
Hi, every one,
In my application , we need to bond my device with host , and then our application will go to deep sleep by calling sd_power_system_off. When I wake up my...
Hi,
I have made some customs pcbs, the main one use the PCA10004 reference design and the small boards use PCA10000. I can get 25 meters on LOS (I think it can go far way...
Hello
Until recently I have been using a JLink EDU to program and test nRF51xx devices from Keil 5.14.
I recently bought a Ulink2 and would like to do the same but have...
Silly question, but I haven't gotten into a good rhythm with the debugger. Every time I try to use the debugger when a soft device is programmed, I can't seem to ever hit...
I'm trying to port the Dual Bank BLE DFU Bootloader to a custom board that we have. The only modification I have made in the bootloader was that I changed it so the internal...
I'm working in a project & I want to use the PWM application provided by the SDK with the bluetooth module, I want to control the LEDs light intensity using the PWM, the PWM...
I'm having difficulty with using PWM library with softdevice. The app_pwm_init function returns
NRF_SUCCESS but call to app_pwm_enable does not generate an output.
...
Hello,
Is that possible to connect to a device that is not advertising ? (a kind of wifi not send SSID)
In my case I know what mac address to connect so it's useless...
The critical section code in app_util_platform is controlled by the symbol SOFTDEVICE_PRESENT. Do I have to set it up in the project or is there something else that controls...
Hi,
My problem is next. I want to use some of examples for nrf51822 on costum board but code stuck at sd_softdevice_enable(). As I cant see where is this function defined...
My computer (Windows 7) cannot find any driver software for the nRF24E1, the dongle PCB in the nRF24Z1 development kit. Where can I find the software?
[edited 7/16] It...
The nRFgo Studio showed "No device detected" when the nRF51-DK board was plugged to the USB port. And the Recover button was greyed.
When the board was plugged in, nRFgo...
Hi,
I want to get a message to know if the S120 center have had get the adv packs.
Is there a way to make a scan respond ack payload pack from the S120 center?
