SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
I am developing a HID keyboard with SDK v6.1, SD v7.3, IC revision 2.
The keyboard is already able to advertise (non-whitelist) and bond with iPhone, and connect/reconnect...
Hello
I want to optimize SPI com as fast I can do:
First I am using the fast spi data rate by SPI_FREQUENCY_FREQUENCY_M8 variable and I want to reduce at first the timing...
As far as i understood it supports 4.2 BLE because using it i'm able to see packets between nRF52 central and peripheral boards (HRM example). Is it so?
Question:
I am confused about who can do (or rather who usually does) whitelisting - the master or the peripheral device?
My findings so far:
I can't find a certain...
Hi,
I have written a windows 8.1 application to connect to my custom nrf51 device. It is used for configuration and is set up without requiring a password (I do not need...
I want to be able to transmit the on-board temperature and battery voltage over a beacon application. The application only needs to transmit periodically similar to an iBeacon...
Dear,
I'm now face problem on button interrupt.
I use 3 buttons for my system.
button 2, 3 is used for boot diagnostics. assigned as below.
bsp_event_to_button_action_assign...
I'm trying to lighten the leds using ble, my problem is that when I measure the current consumption when the leds command sent, it reaches to 5mA which is not suitable for...
Hi
I've playing around with the new peer manager a while. I used the example "ble_app_hrs_rscs_relay_pca10028.uvprojx" from the SDK10. After a first fix (see Link ) in...
Hi,
I want to use timer1 or 2 interrupt ISR to generate complicated PWM signal.
but the timer->intenset setting cause ble connection drop problem.
Please refer to my...
Hello. I'm having the following connection module with nRF51822 chip.
It was purchased here .
I've found example sketch for Arduino but i can't understand how to wire...
Hi,
I have been developing using some development modules from WaveShare (based on the nRF51822 QFAC) and they work fine.
However, I'm now trying to use a module better...
Hi Nordic Expert,
I am Alex and have been developing with NRF51822 for a long time. Thanks for your quick help before. Now our product bases on S110-7.1.0 and SDK-6.1.0...
Hi
i wrote the program which is making pulse one time on channel 0 and then followed by channel 1 and then again channel 0 and then 1 going on , my aim is to create pulses...
Hi all,
I am tring to connect more than two peripherals to contral device.
I am using sdk10 and three evaluation bords nrf51822.In on device i debbuged the code of uart...
