Hello community,
I am trying to develop a custom bluetooth HCI_USB code for the BL5340PA BLE controller board. The Liard Connectivity's(now Ezurio) BL5340PA : https://www...
Hi
I use nRF7002-DK, SDK:V2.5.2 with zephyr driver, I need to send recieved data or command from uart, data type is using with hex byte array to send, from example , the...
Hello support team,
I am a beginner in this environment and I am facing a problem while trying to compile my project in Zephyr for nRF52840dk board. I am trying to run this...
Howdy guys,
I am using an nrf52840 and SDK version 17.1.0 alongside Keil. I just upgraded from using the arm compiler version 5 to 6, which required me to switch from the...
Hello,
I have an nrf52833 that interfaces with an external flash module. It is configured to store mcuboot's secondary partition. I am able to write the secondary image...
Current goal is to be able to program, and upgrade with the radio off, and the only connection as a UART.
But I'm both overwhelmed by the number of options (DFU, SMP, and...
I'm using 2 nrf52840dk, ncs2.5.0; running the central_uart and peripheral_uart examples, I want to know how to send a string without pressing the "enter" key. For example...
Hi I would like to report a bug in the Devicetree visual editor.
When you add two fixed regulators and connect a separate sensor to each of them, both sensors will be represented...
Hello ,
I have a few questions about the connectivity bridge on T h i n g y : 9 1 . I 'm currently working with Bluetooth data on the nRF52 SoC and I need to transfer it...
I have a Raspberry Pi Pico which is powered by a Lipo battery. I want to measure the current with the Power Profiler Kit II. I hooked the 2 grounds to to the board, and VIN...
Hi,
TWIM does not work well with nRF5340DK as shown in the subject. The conditions are shown below. - I/O voltage is not 1.8V. The waveform is distorted around 2.5V, though...
Hi,
I am having a hard time for days now trying to get the MCP2518FD working on a nRF9160-DK board. This device, embedding CAN transceiver and receiver, is accessible through...
I am trying to get a SST25 spi flash running, but the jedec,spi-nor driver does only partially work.
As i understand now the jedec,spi-nor driver only works with CFI compatible...
Hello Team,
We would like to keep the necessary build configuration for a board in Bitbucket,which are necessary to show up the "Build" folder in VS code.So that every developer...
Hi, I am experiencing low power issues on a nRF52840 DK 3.0.2 board which I have not seen on another one with version 3.0.0. I do not know the root cause yet.
For my investigations...
Hi
I am powering the nRF52840 from a 3.3V DC power supply and connecting it with a IMU thats cannot go higher than 1.9V on the I2C bus
I use 1.8V.
Will the I2C coomuncation...
Hi All,
My issue is may connected to
I'm using:
nRF52 DK dev. board
nrf52dk_nrf52832_defconfig
I get communication errors very several times. (More than...
Has anyone succeeded in BLE bonding with a Philips Hue lamp or a smart plug with a nRF52? Directly with BLE, without a gateway. I suppose I have all the rest figured out,...
Hi,
I have a new NRF5340-DK and I am trying to connect it via usb on linux but do not see it in the syslog when connected. I actually do not see anything at all.
When...
Dear All:
I found that there is a shell interface for the nrf5340_audio project.
I wanted to test the sd card playback from the shell interface.
For the broadcast sink...
Hi,
I want to implement a pwm output signal on a particular pin of the nRF52840DK working with the latest nRF Connect for VS Code. What would be the recommended way to setup...