Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi all,
we are using nRF52810 and SDK 15.3.0
Project is based on central and peripheral concept .
we are facing issue with the peripheral BLE power consumption.
...
We are building a solution for a large OEM where we have BLE tags on inventory trolleys and employees. When the trolley is empty, the BLE tag on the trolley would send a notification...
Hello,
i am working on nRF52832.
i was successfully build a code for scanning without using FreeRTOS
Now i want to use FreeRTOS with my scanning code
But i am not...
Hi ,
i am using ble ancs profile in my project, i was getting internal error (error no 3) while connecting.
the error is being reported by two of the following event handlers...
I have managed to establish a proper TLS connection with the proper credentials, but it seems that TLS session resumption is missing from my implementation since my device...
Hello:
I am now working with nrf5_SDK_for_Mesh_v3.0.0 and I try to implement OTA for mesh dfu. However, I found that the v4.0.0 has a dfu_no_serial_nrf52832_xxAA_s132_7_0_1...
Hello,
I've just recently started learning to develop on the nrf52 platform after 2 years of frustration trying to learn of how to develop on the Nordic platform I finally...
I am trying to set the Lifecycle state of the cryptocell, but it seems like I am having an issue.
I do
/** Enable crypto cell to configure it **/ NRF_CRYPTOCELL->ENABLE...
Hi,
I have fanstel BM833A modules which is NRF52811.
I am using Segger Embedded Studio.
How can i program the module through segger IDE using ST-LINK?
And also i have...
Multi link ble + zigbee multi-protocol testing is currently underway. The main purpose is to test the packet loss rate and throughput of radio time-division multiplexing zigbee...
We've had so many problem with Bluetooth Smart DFU on nRF52832 that I've decided to write a ticket here and ask for help. We've been reading lots of documentation, following...
We want to change the communication speed for each connected peripheral.
*Environment
Peripheral: nrf52832
Central: nrf52840
*Step 1. After the peripheral connects...
Hi all,
My project will use PPI to control COMP of nRF52832, connect Event of COPM and Task of GPIOTE.
Question 1,
How could I get the address of COMP event and use...
