Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi,
I would like to debug the code which is in Nordic Thingy91 by using nRF52840DK.
Is it possible to use the debugger in nRF52840DK for Nordic Thingy91 ?
If it is possible...
Hi,
I like to understand what SBs should I cut, what switched should I use to measure the SOC current only with PCA10056 board. I use the Otii Arc device to supply power...
Hello,
I'm working on NRF52832 based module BMD-301
for same i'm using SDK16 Segger Embedded Studio
The thing is
when uploaded ble_app_alert_notification example it...
Hello,
I've tried to convert the mesh light switch server example from NRF52840 DK to Dongle following this post.
Unfortunately that doesn't work.
I've changed the BOARD_PCA10056...
Currently, there is a project. The situation is that the master nRF52840 communicates with the cloud server through the GPRS232 module, the slave nRF52840 communicates with...
Hi,
I tried to create a custom server in using server setup of nRF Connect v3.3.0 but when I tried to apply my custom server on my device, the software bugs instantly. ...
I want to modfiy the code in the example ble_app_ancs_c to read the internal flash with fstorage. But after I set APP_TIMER_CONFIG_USE_SCHEDULER to 1, the operation of fstorage...
Hi every one, I am running light switch example (using SDK 15.2 and SDK for Mesh version 3.1.0 ). The problem is: My provisioner node cannot Receive RSSI message of a node...
I am trying to save and read a structure using FDS, how do I go about it?
I have the structure:
My custom function for saving is:
I call the function using below...
This error always stop the "mqtt_simple" application.
I have tried modem versions 1.0.1 and 1.1.0, SDK versions v1.0.0 and v1.1.0 and added this code to system_nrf9160.c...
I have an Android application running with RxAndroidBle library and I want to change it to Nordic-Ble-Android library. I'm not that good with Bluetooth and the actual version...
Hello, i'm new in BLE and i would like to know, what is the best way to read and write 200-300 parameters of my product via BLE from a phone?
Possibility 1 is, to create...
I am trying to save and read a structure using FDS, how do I go about it?
I have the structure:
Is this correct by populating the record as such?:
And to read...
Hello,
is there any tutorial on how to send commands to the Thingy52 from an Android app (like the Thingy52 app or nRF Connect) to start the RTC clock (and then read/clear...
My 52833DK is apparently bricked. I get the message "Could not find core in Coresight setup. Abort debug session” When I try to load code (IAR) into the board. It was working...
