Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hello:
I am now working with nrf5_SDK_for_Mesh_v3.0.0 and I try to implement OTA for mesh dfu. However, I found that the v4.0.0 has a dfu_no_serial_nrf52832_xxAA_s132_7_0_1...
Hello,
I've just recently started learning to develop on the nrf52 platform after 2 years of frustration trying to learn of how to develop on the Nordic platform I finally...
I am trying to set the Lifecycle state of the cryptocell, but it seems like I am having an issue.
I do
/** Enable crypto cell to configure it **/ NRF_CRYPTOCELL->ENABLE...
Hi,
I have fanstel BM833A modules which is NRF52811.
I am using Segger Embedded Studio.
How can i program the module through segger IDE using ST-LINK?
And also i have...
Multi link ble + zigbee multi-protocol testing is currently underway. The main purpose is to test the packet loss rate and throughput of radio time-division multiplexing zigbee...
We've had so many problem with Bluetooth Smart DFU on nRF52832 that I've decided to write a ticket here and ask for help. We've been reading lots of documentation, following...
We want to change the communication speed for each connected peripheral.
*Environment
Peripheral: nrf52832
Central: nrf52840
*Step 1. After the peripheral connects...
Hi all,
My project will use PPI to control COMP of nRF52832, connect Event of COPM and Task of GPIOTE.
Question 1,
How could I get the address of COMP event and use...
hi.
I wonder if nRF52840 dongle has an unchangeable bootloader, and if so, where we can download it. PCB of nRF52 dongle is available on the official website, but not in...
Hi there,
in my passion to keep up with technological advances, I ordered the nRF5340 PDK. I was hoping to pave the way of moving our nRF52832 and nRF52840 based projects...
Hey guys,
I'm working with a Laird BL652-SA Development Kit and downloaded the Nordic SDK v14.2.0. I want to try the UART example, but after the build comes a semantic error...
I'm not able to get working my PPK.
I've followed the guide, installed the Power Profiler app with the latest nRF Connect v3.3.0, cut SB40 on my nrf52840DK and set correctly...
Hi,
I wanted to know how to change the frequency from from 16Mhz to 64MHz which is processor frequency. I know the HFCLK is 16MHz but how to use the 64MHZ frequency.
Regards...
