We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
If you look at the secure bootloader example the nrf_bootloader_init(...) never return to main scope unless an error occurs.
Everything is handled inside this function even...
The " 5.3.6.8 Reset behavior " table in nRF52840 Product Specification v1.1 mentions that WDT reset does reset the WDT itself.
I'm trying to reconfigure the WDT after a...
Hello,
I am using HC-SR04 ultrasonic sensor and nrf52840dk. To measure the distance I have to find out for how long the ECHO pin of the sensor remains high.
for that I...
On my old Wondows10 development computer, all worked OK.
In a brand new Windows10 laptop, all up to this point installs/verifies fine using nRF Connect.
I cannot find...
Hello, I'm making a PCB project with nrf52832 and I want to use my debuggers only 2 pins(SWDCLK and SWDIO) to debug it. I have J-Link Edu, but I wonder if I can use it with...
Hi, All.
I' m studying nRF52832.
I have a question about example "ble_app_uart".
I m trying to send to smartphone using function "printf()".
Uart pins(RX, TX) are...
Hi everybody! I have a code running excellently on my nRF52840 DK. I would like to make it run on my nRF52840 dongle. What should I change in my SEGGER project? Can anybody...
I am building a project which requires accelerometer data from the LIS3DH accelerometer be read and then transmitted over bluetooth. I have successfully setup bluetooth transmission...
Hi,
For my project I need to receive 9 bytes of data from our main board. This data gets send using UART.
By looking at the pin diagram I could not find specific pins...
Hello,
I am running nRF Connect for Desktop v3.2.0 on Win10 64-bit machine. Everytime I launch an applet, such as Power Profiler, I get a new blank window and nothing happens...
Hi, I am having a problem changing information advertised by the Beacon while the application is running. I started with the app_ble_template example and added Information...
I have an nrf52832 dev board with me and I'm using nRF5_SDK_15.0.0_a53641a SDK version. I'm using the project " pca10040_ble " inside the " secure_bootloader " folder from...
Hello,
We are evaluating Thingy:91 for NB-IoT. We want to validate the RF transmit test and are using %XRFTEST command.
The syntax is as follows, AT%XRFTEST=1,1,3,18000...
The TWI_Scanner example is building and downloading fine (using SES) but it just prints:
"TWI scanner started."
Then nothing in terms of scanning addresses etc.
It does...
