Hi everyone,
I'm facing an issue where MCUboot doesn't perform a swap after reboot, even though the DFU download to slot 1 completes successfully and boot_request_upgrade...
I am getting the following build errors when working with both DFU (MCUboot) and the file system (FAT FS) together. Errors: D:/ncs/v2.9.0/zephyr/drivers/disk/flashdisk.c:533...
Hello,
We are working on an audio project where we are using nRF5340 Audio DK. We want to externally interface the digital microphones without using the on-board codec ...
Hi, We want to integrate LORA LR1110 for the final year capstone project. From the documentation we have understood that Kit is fully compactable with Arduino UNO. But SPI...
안녕하세요
nrf9160DK 보드로 개발하고 있습니다.
blink 예제로 컴파일 및 다운로드되었음을 확인했습니다.
SDK에서 예제AWS_IOT_MQTT로드하여 테스트하고 있지만 아래와 같은 오류가 발생합니다.
해결 방법을 가르쳐 주시면 감사하겠습니다.
zephyr/subsys/net/libsubsys__net...
I'm trying to run Wi-Fi scanning or AP/STA mode examples on the NUCLEO-U575ZI-Q board with the nRF7002EK shield, but I keep getting an "RDSR2 register failed" error. I've...
I have developed the schematic of connecting NRF 8001 BLE chip with Arduino,the file is attached that contains the schematic. Can you please verify my schematic i.e will it...
Hi, I'm looking for a solution can make a ble device communicates with multiple 2.4g devices at the same time , is 51882 qualified for this? or just by combining both nrf8001...
Hello,
I would like to use the fifo common library but i have an link error. I don't understand that because fifo_app.h is included and contain the functions...
...
Hi
We are using indication to send data to make sure master receive all the package.If we didn't
receive the confirm message,what should we do?Should we send it again in...
I'm guessing it is because the engine powering the site does not support it. But has it ever been considered?
I think it is a powerful way to engage users and build a community...
Hi,
I have two questions about nRF24LU1+.
Q1
Can i change nRF24LU1+ isocheonous endpoints(Endpoint 8 IN/OUT) to Endpoint 1 IN and Endpoint 2 OUT?
Q2
Can i use Endpoint...
Hi,
we’re a group of students at NTNU in Trondheim doing a project regarding bike and pedestrian registration. So far we want to make a solution based on iBeacon and Bluetooth...
Hello,
I am looking into the possibilities of implementing frequency hopping using the nRF24L01+ radio with an external Ti MSP430 microcontroller. I have read that it's predecessor...
Hi,
I want to realize the function of bond, I use "lib_aci_bond(180/* in seconds */, 0x0050 /* advertising interval 50ms*/);'\",.When I click the connect, it can connect...
In nrf51_sdk_v4_4_1_31827\nrf51822\Source\console\console.c,
#include "uart_legacy.h"
But there is no "uart_legacy.h" file in the SDK.
I have to modify to "app_uart...
I downloaded the source for the Android UART app, hoping to hack it into something I can use to test my gadget. But it's incomplete: it fails with the message:
Missing...
I have 3 short questions:
Does S120 support or will support swiching over BLE and Gazelle like S110 does?
Will be able in future to be connected to a BLE...
Hi,
If I want to send data(400Bytes) to client(phone),I must use sd_ble_gatts_hvx to notify client. Is it right?
Every time I notify 20bytes until the end, is it right...
