before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hello, my application requires very precise timing to trigger an action on the edge of the GPS time. I just need to get this time once in a while to synchronize the system...
Hello,
We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
Hi Nordic team,
This is a follow-up to my previous question here:
Can nRF52833 perform PAwR while also syncing to another PAwR device?
We are now extending our design...
Hi,
1.As shown in the following PSM eDRX figure, during the red period, how will the text messages sent to nRF9160 be processed? Will the nRF9160 module receive them in...
Hi guys,
For a client of mine I'm working on an openthread RCP implementation using a SolidRun N8 that contains the NRF52833.
I'm using ncs v2.9.0-nRF54H20-1.
The problem...
Hi Nordic team,
We are developing two types of devices based on the Zephyr examples:
periodic_adv_rsp
periodic_sync_rsp
Our design uses the following...
Hi! We are having problems pairing a nRF52840 against linux (ubuntu 25.04). Pairing fails instantly, before any passkey is shown on the host, returning with code 9. Short...
Hello everyone
I need help. I have a custom board that uses the nRF5340 microcontroller. I am using the Zephyr OS and nRF Connect SDK Toolchain v2.9.0. How do I update my...
I use the security mechanism dtls based on udp communication. Can I implement it on nrf52833? How much flash and ram should be occupied at least? Is there a suggested value...
I am using NCS 3.0.0 and I want to generate keys ... But the method I am using to generate keys is giving me this error Here is the code where it is returning error:
psa_set_key_usage_flags...
Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
fail to erase an nRF 5340 DK. Can't recognize the COM. But board is recognized as J-Link driver. Does anybody know why this happen? the log is as follows:
2025-06-16T07...
Hello
No reply so I am writing again. The LCD operates normally using the source as shown below.
https://github.com/Exboom/GC9A01_nRF52
However, the screen does not...
We are currently working on a project using Enhanced ShockBurst (ESB) and would like to enable Front-End Module (FEM) support with the nRF21540.
According to the Enhanced...
Due to production requirements, I need to obtain the device's QR code. However, I found that the QR code can only be retrieved using the code snippet below after calling Nrf...
