FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
Hello,
We are developing an application which is using the app_scheduler (especially to put events etc.)
It seems that sometimes (very rarely) we detected a Hard Fault...
I have 4 buttons in my circuit with a nRF51822QQAC (a RAYTAC MDBT40 module on a custom PCB), I am using a very simple printf to check which ones are pressed, the internal...
I've followed this for assistance, but I'm stuck:
https://devzone.nordicsemi.com/question/17846/nonvolatile-memory-access/
I can read from flash, but I can't write to...
Hi
I wrote a softdevice, bootloader and application using the nRFgo Studio.
When I turn on the device, bootloader_settings_t is all 0xFF so bootloader_app_is_valid returns...
I went to so many references and definitions of variables and functions but I can't seem to find where is decided to use either spi_master_0 or 1.. where is this magic config...
I am a freshman. And I am doing some research on BTLE by nRF51822-EK. I want to get RSSI. Could you please tell me if there is a reference code or project in SDK? Is there...
Hey,
For my project I wrote and tested (w/ nRF51 DK) all firmware in mbed. I also made a custom PCB w/ the nRF51822 CEAA chip based on the 4 layer reference design provided...
HI,all!
I want to know if BLE can send data to APP in form of String instead of Byte?(the examples all send in form of byte )
If it does can, can you mainly introduce...
Hey everyone,
I'm trying to print floating point numbers to the UART to debug my application. I know the nrf51 is doing the operations correctly because if I convert the...
Hi,
I'm using the following TI IC www.ti.com/.../tps62736 to get 3V from a LiPo battery. It has a VIN_OK pin that I can configure to alert of battery low level. The problem...
Hi,
I am trying to get even a basic ARM GCC example set up using the provided toolchain code, and am having a rough go at it.
First, what is the most recent, working...
In the s110_nrf51_8.0.0_migration-document.pdf, the ROM and RAM start and size for the v7.0.0 and v8.0.0 are specified as follows
s110_nrf51_8.0.0
IROM1 - Start...
What should the connection or other settings be to have a peripheral always connected? It is a bit contradictory for low energy device, however for a lost&found (link-loss...
Hi,
I just started on developing on the nrf51-DK. I started with blue_app_proximity, and I am trying to hack the immediate alert to do a toggle a led. I initialize the...
