I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
I have a nrfgo 6310 start kit that I use for my nrf51822, but I'm wondering if I can also use the nrfgo 6310 for the nrf24Lu1 development kit as well? I tried plugging in...
Hi All,
I am working on the S120 bootloader.
I start it with dfu sample on nrf6310 folder. It work with S110 softdevice with PCA10001 perfectly.
I had made following...
Hi,
I would be grateful if someone could guide me a bit.
As far as I understand, nRF24L01+ implements Enhanced Shockburst technology in chip. To use nRF8001 as drop in replacement...
Hi all,
I am using s110 v7 for scanning and advertising, it works well. Now, I would like to measure RSSI while scanning (already scanned device but not connected) . Can...
Hi,
I am using nRF5182. Kiel is the IDE. I need to operate the device in 25Mhz. How can i change the clock frequency to 25Mhz. Is it possible? Will it affect the operation...
Hi,
I just stumbled upon the nAn-36 note ( www.nordicsemi.com/.../80193304 ) and I have two comments about it :
I think it's the best technical documentation I've...
Where to find definition for INTENSET/CLR for TIMERs in 'nRF51_Reference_manual v1.1'? I think I've read it all by now, but still can't find it.
After some digging I found...
If I have the PC insert 1msec byte spacing between data bytes sent to the NRF51422, it receives the message and doesn't reset. I can send messages less than 10 bytes to the...
my code shows here: github.com/.../main.c
uart_init();
printf("\r\n\r\n");
printf("\r\n __DEBUGGING__\r\n");
every time my app started, it always shows corrupted...
Is there any more information available on a release date for the next rev of the 51822 which is supposed to have better handling of concurrent A/D and radio operations? ...
C++ BLE_API of mbed, which I want to use offline with Keil-MDK, looks really well-thought & coherent to me, but I am not a guru in SW development.
Since the mbed-platform...
The NRF51822 PWM examples I have located work by toggling GPIOs. Does the device have a more sophisticated mechanism than this for generating PWM signals? More pecifically...
Hi all
In my application where I'm using the Soft device 6.0, I have a simple function which is very time critical. However, this function is not called very often, but...
Hi,
Please can you send me the ble_app_uart source code as it is missing from the latest 6.1 SDK.
I have the PCA 100003 & PCA10000 boards.
Many thanks.
Hi,
In my application I use 5 devices and 1 host to communicate.
I have only a few packets to transfer so the data rate can be low (22Byte/transmission).
The devices...
