Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I am trying to create a trilateration system with 3 initiators and 1 reflector (Hopefully multiple reflectors in the future) on the nrf54l15. The channel sounding with...
I'm trying to add diagnostic logging functionality to my Matter project using SDK version v3.0.1. I followed the steps outlined here: ( https://docs.nordicsemi.com/bundle...
Hello! I have a Nordic Power Profiler Kit 2 that I am using to make measurements on a project. The issue I am having is I get an error message when trying to connect the kit...
Hi,
I'm using nrf Connect mobile (for Android) app to exchange data (read/write) with a BLE device (server) over GATT.
I have a large characteristic (123 bytes) to exchange...
Man,do you have the experience on DIY Bluetooth headset with PCA100059?
I raise this question for I hate the current product limit: limited time to run,short lifetime of...
Hello, I've a nRF9161DK board and I would like to connect a UART to an external device.
Looking at the schematics I see that both UART0 and UART1 of nRF9161 are connected...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
I have several hardware pieces based on the Fanstel WM02C nRF7002 module (nRF54L15 host) and am having problems connecting to WiFi networks on a subset.
All modules successfully...
toochain:3.0.2 sdk3.0.2 nrf connect Every time I build, it gets stuck here: Found assembler: C:/ncs/toolchains/0b393f9e1b/opt/zephyr-sdk/arm-zephyr-eabi/bin/arm-zephyr-eabi...
Hi, we are developping a medical device that receives an audio stream from a smartphone. We have a custom board connected to a different DSP than the one in the nrf5340_audio_DK...
Hi, I am using two nRF54L15 DKs running THroughput samples.
The result of coded s8 is 52kbps, which is close to the theory number.
When I change to S2 code, the result...
I upgraded from v2.7.0 to v2.8.0 of the nRF Connect SDK and noticed that the UART was no longer working.
It seemed the UART receives one byte and calls exit. Transmit doesn...
In our development using NCS-2.6.1 it is desirable to have logs using BT NUS.
"Serial Bluetooth Terminal" android application is used.
For testing purposes NCS\v3.0.2...
hello Nordic
i am working with nre52840 and nrf52832, with ncs v2.8.0
i am using ble SMP service for transferring data with a central device and for DFU.
currently i...
Dear forum, We are using the nrf5340-DK development boards as an intermediate link to flash our own boards containing the nrf5340 chip. This is possible since there is an...