Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
hi support team,
i have one problem for 54l15+7002 in ncs2.9.0
I am afraid that I need your help.
I was porting MQTT demo and PERIPHERAL_UART demo together and want...
I have a nRF9151 currently set up to observe a CoAP resource on my server. The initial GET request works, and if I respond with new updates from the server (within a few seconds...
Hi, guys. I encountered some software issues while using VS Code for development on the nRF5340 DK. During the build configuration, the code reports an error saying it cannot...
Hello, recently I bought the Seeed XIAO nrf52840 because I read in the datasheets the power consumption of the microcontroller is 400 nA typical in SYSTEM OFF mode without...
I am using VSCode with nRF extension with the latest 2.9.1 SDK.
I have been working on an application for bluetooth for the 54L15-DK.
I want to do a custom sensor driver...
Hello DevZone,
I have an nRF5340 devkit along with an nRF7002EK, and I'm looking to upgrade from SDK version 2.6.1 to 2.6.4. However, I'm facing an issue. In version 2.6...
I conducted a BLE test using two nRF52840 Dongles. Since I used Dongles, I based my code on the usbd example from the sample programs. During testing, the connection between...
Hi, I'm working on a project where we would like to track system performance using Segger Systemview. I'm building with the following RTT configs: and I'm getting the following...
NCS 2.8.0
Ble device acting as both central and peripheral.
CONFIG_BT=y CONFIG_BT_LL_SOFTDEVICE=y CONFIG_BT_DEVICE_NAME_DYNAMIC=y
#for cenral devices these are set....
I am an experienced user of the Nordic Distance Measurement Library and I am encountering an issue where the device that is assuming the role of the DM_ROLE_INITIATOR can...
Hello Nordic Team,
I'm currently integrating a watchdog on the nRF5340 CPUNET core to detect and recover from potential hangs. We’ve observed that in rare cases , the device...
Hello everyone,
I trying to configure my MDBT50Q-U512k to use the ble_app_nus example. According to my board, I need change to uart pins defined in this example. Then, I...
hello everyone,
I am currently doing an project that is hoping to achieve this result: nrf52840 connect to my phone or connect to my computer via ble, then there will...
When working with the direction finding central code, would we need to have the antenna array connected to the central development kit and then have another kit running the...
