I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hi Nordic Team,
I am using NCS v3.0.0 and working on a Matter-based application.
I have enabled the ActiveHardwareFaults attribute (0x0005) in the General Diagnostics...
Hi, Goal: Send a firmware update from nrf5340 to another nrf5340 over BLE I found the following sample and a lot of support tickets talking about this sample but I am unable...
Hello,
I recently tried some examples with nRF53 + nRF7002 (e.g. ble_coex example).
However, I am developing with nRF54 and I would like to understand if the combo nRF54...
I am working with the DWM3001CDK board for Ultrawide band, but would like to use one of the free LEDs on (P0.14, P0.22, P0.05, or P0.04) as a way to show that the 3 AAs powering...
Hi,
We’ve designed a project using the nRF5340 + nRF7002 combination, with Wi-Fi connectivity enabled.
As part of our preparations for FCC certification, we’re currently...
We designed a nRF54L15 custom board and now want to add nRF21540 FEM module to our device tree as follows:
/ {
nrf_radio_fem: name_of_fem_node {
compatible = "nordic...
I will attach my main.c and skd_conifg, maybe i'm overseeing something in code. Also i will attach schematics and pcb. I'm aware of RGB led consumption, in reality it's around...
Dear DevZone,
While porting our project from NCS 2.9.1 to NCS 3.0.0, I ran into linker errors when building LVGL. The linker reports that it cannot find functions defined...
How do I map the build codes noted in the Rev Errata to the stamps on our ICs? I have two versions with QFAAAB and QFAABB stamped on them but the documentation says QFAA-B00...
I'm developing my product using NCS. It compiled fine yesterday, but today when I opened VS Code with the nRF Connect extension, it prompted me to install the toolchain. I...
Hi,
We have some GPIO pins where we want to change their configuration during runtime. We want to switch them between input pull down and output. Is this possible?
When...
Hello, I want to disable parts of my RAM to save power. I implemented this in my project based on the System_Off ram retention example. I'm now not sure if RAM retention is...
I noticed that the product information of the nRF54L15 series kit supports 4Mbps, but I'm unsure how to verify it. Are there any relevant examples available? I have currently...
Dear Nordic Support Team,
I am experiencing difficulties flashing firmware to my nRF52832 development board using VSCode with west flash , followed by J-Link...
Hi, We are using nrf Connect SDK 2.4.0 and have been looking through the NIST vulnerabilities databases. One of the vulnerabilities reported with the nrf5340 is a denial of...
