Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Man,do you have the experience on DIY Bluetooth headset with PCA100059?
I raise this question for I hate the current product limit: limited time to run,short lifetime of...
Hello, I've a nRF9161DK board and I would like to connect a UART to an external device.
Looking at the schematics I see that both UART0 and UART1 of nRF9161 are connected...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
I have several hardware pieces based on the Fanstel WM02C nRF7002 module (nRF54L15 host) and am having problems connecting to WiFi networks on a subset.
All modules successfully...
toochain：3.0.2 sdk3.0.2 nrf connect Every time I build, it gets stuck here: Found assembler: C:/ncs/toolchains/0b393f9e1b/opt/zephyr-sdk/arm-zephyr-eabi/bin/arm-zephyr-eabi...
Hi, we are developping a medical device that receives an audio stream from a smartphone. We have a custom board connected to a different DSP than the one in the nrf5340_audio_DK...
Hi, I am using two nRF54L15 DKs running THroughput samples.
The result of coded s8 is 52kbps, which is close to the theory number.
When I change to S2 code, the result...
I upgraded from v2.7.0 to v2.8.0 of the nRF Connect SDK and noticed that the UART was no longer working.
It seemed the UART receives one byte and calls exit. Transmit doesn...
In our development using NCS-2.6.1 it is desirable to have logs using BT NUS.
"Serial Bluetooth Terminal" android application is used.
For testing purposes NCS\v3.0.2...
Dear forum, We are using the nrf5340-DK development boards as an intermediate link to flash our own boards containing the nrf5340 chip. This is possible since there is an...
Hello,
We are working on an audio project where we are using nRF5340 Audio DK. We want to externally interface the digital microphones without using the on-board codec ...
Hello,
I'm looking for answers and some explanation for two main questions - is it possible to perform non-simultaneous multi-image FOTA over WiFi? Is it possible to support...
I am getteing a -12 error when trying to access a open/create a file using littlefs and a fs_open command on a nrf5340 custom board.
The filesystem seems to be mounted fine...
Hi all,
Our company is currently prototyping with the Nordic 91X DK and looking to use both nrf cloud services specifically for using location services whilst also connecting...
Hi Nordic team,
I’ve been working with the nrf_dm sample from NCS 2.9 to perform distance measurements using multiple nRF52840 devices. The sample works well, and I've made...
