Hi, We want to integrate LORA LR1110 for the final year capstone project. From the documentation we have understood that Kit is fully compactable with Arduino UNO. But SPI...
I have several hardware pieces based on the Fanstel WM02C nRF7002 module (nRF54L15 host) and am having problems connecting to WiFi networks on a subset.
All modules successfully...
Hi all,
Our company is currently prototyping with the Nordic 91X DK and looking to use both nrf cloud services specifically for using location services whilst also connecting...
nRF54L15 would be used as thread RCP, host processor would use uart to communicate with the rcp. They would behave like a OTBR.
I also need to do device firmware update...
Dir Sir
I have bought thingy 91 X for evaluation purposes
After activation of the Sim and, I have a constant green Led on
The device does not connect to the web application...
Hi
I have two DKs, previously they work well, however, after I add the nRF21540 FEM on each DK, I always receive this in my central device:
Whether the amplifier cause...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
I am a beginner to BLE Communication ,
Currently I am working on a project where I need to connect a peripheral device ( Central (nRF52840) ---> Peripheral (BLE device)...
Hi all,
I may have encountered an issue with nrf9151DK board.
When I only set LED1 with dk_set_leds (DK_LED1_MSK) the LED1 and LED2 are both lit.
Setting other leds...
im looking for a developer that can help me work with the NTN functionality of the 3GPP release 17 of the NRF9151-DK so if you are interested please write to me at eric@zerocool...
Hi everyone.
I am using Visual Studio Code. When i try to compile a simple blink_pwm project, I could not. I am sending output in terminal. What is the main problem and...
Hello!
I am working to design and build a custom PCB using the nRF7002 chip and came across this callout on the schematic diagram and wanted some clarification about it...
Hi,
I designed a custom PCB with the nrf5340 CLAA chip and am testing out the board. I want to flash a simple project of lighting up the on-board LED (the LED is connected...
Hi, I'm currently working on an application with the nRF9151, and will use the shadow concept to change parameters used by a device externally connected to the nRF9151. Intended...
i'm already able to TX and RX arbitrary packets between my own bare-metal test programs running on a pair of DKs... since both programs used identical configurations (mode...
Hi,
We are on NCS v2.9.1
We have an existing project on based on the nrf52832, which we use as a hci_spi controller. There, CONFIG_BT_LL_SW_SPLIT is set. We are now porting...
Hi Support Team
We try to integrate the flowing links' sample code of Mesh Sensor, Mesh LPN and Mesh DFU to one project for nRF52832, but we found that the memory usage...
i'm migrating my application from nRF53 (SDK 2.6.0) to nRF54L15 (SDK 3.0.1) and i've started to get crashes in the soft device.
sometimes it reboots without any logs at...
Dear Nordic team,
i am stilll struggeling with the GPIO set-up in system off mode. It seems, that both GPIO_INT_EDGE_TO_ACTIVE and GPIO_INT_LEVEL_ACTIVE are working fine...
Hi
I had a device that did not start up - because it was waiting for the 32KHz clock to be stable.
So I tried to change the setting below from 15pF to 5pF and it started...
Hi Support Team
We try to integrate the flowing links' sample code of Mesh Sensor, Mesh LPN and Mesh DFU to one project for nRF52832, but we found that the memory usage...
Hi there.
I am trying to implement a 16-bit, 32kHz, 2 channel i2s interface which is being fed by a FIFO (the final source of this FIFO will be a DAB/FM radio module but...
