Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I am trying to do the dfu update in my custom flutter application like it does in the nrf connect application. My device is correctly being put in bootloader mode and the...
Good day,
I am trying to program the nRF Sniiffer firmware to my nRF52840 dongle using the "nrfutil device program" command.
According to the User Guide v3.2 for the nRF...
Hello,
My new dev kit is not being detected by Windows Device Manager right out of the box. I've tried multiple USB cables and I've confirmed VBUS=5V is present on the input...
Hi,
Programmer can't read chip information after i download firmware with VSCode.
Before download, Programmer can read chip information.
Tool : Visual...
Hi all,
I applied QSPI driver on NCS 2.4.0 with QSPI LCD panel and I encountered the problem.
The red area is the data I sent, but the blue area is not what I sent....
Hi everyone,
we are trying to use the TWI interface of the nRF52832 to communicate with a TI BQ28Z610 fuel gauge, using the TWI driver of the nRF5_SDK_13.0.
For the last...
This sounds like a stupid question... but I would like to clarify if this pin is an input or output. I think it's power in but want to make 100% sure as I'm spinning a PCB...
Hi , am working on nrf52840 .with nrf desktop v2.9.1 . I am working on display ST7789V with the nrf52840 using Zephyr. I have integrated overlay file . while working on it...
Hi team, According to this statement, it indicates that access port protection can be deactivated by modifying the TAMPC.PROTECT registers, which can be achieved by executing...
I'm currently working on configuring the nPM1300 used in our custom board. In the product spec v1.2, it supports 2 USB compliant current limits, IBUS at 100mA and IBUS at...
I am trying to add Coded Phy to my Zephyr BLE Mesh project. I know this is not officially supported, however is possible. Running the stock BLE Mesh Zephyr sample, I keep...
Hi, We are currently working on a new product based on NRF54L15. Goal : We are trying to set up the "Bluetooth LE UART service" example in order to transmit and receive data...
Hi,
I'm doing a test with a matter test harness. An error occurs in test case _TC-CNET-4.16, _TC-CADMIN-1.22 and _TC-DGGEN-2.3.
1. _TC-CNET-4.16: Step 2: should receive...
Hi Nordic team.
We are developing the LE audio product, and have questions here.
We have design a headset board using the RT5616 as codec.
The modifications here are...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
