Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi am trying to use Nrf54l15 as a controller with an external host for the Channel sounding feature. I can receive CS subevents from the NRF controller, but the same thing...
Hi
I'm migrating applications I wrote using SDK 17 to nrfConnect 3.0 with Zephyr.
I implemented USB devices with combined multiple USB classes. One of those classes was...
Hello-
I'm working on our design for the nrf9160 and I've been trying to wrap my head around the FCC certification. I know that the nrf9160 is an FCC certified module and...
I am developing a project in which a weight analog data is converted as digital by Aviva HX711.
In the host board NRF52840DK, I want to read the wight value.
I have attached...
Hello, I am new to BLE and nrf zephyr programming. I am trying to flash periodic_adv and periodic_sync samples ( https://github.com/nrfconnect/sdk-zephyr/tree/16bcaed54230e3d86aeaf2b2f1d47393967254fd...
Hello,
I would like to use the Radio Test Sample from the newest NRF Connect v3.0.2 (v3.0.2\nrf\samples\peripheral\radio_test). However, when I try to build it with "nrf54l15dk...
As the poster above mentioned, the nRF54L15 ENGA version is stuck when initializing the GRTC.
it gets stuck at nrfy_grtc_sys_counter_start().
The SDK is 3.0.2.
Is there...
We are developing a BLE application with nRF52833 512kB ROM size and using NCS v3.0.2. However it seems the ROM size occupied is not so logical, or the ROM size for NCS (Zephyr...
I am using the nRF54L15 on a custom board where I have good control and knowledge about what is going on regarding current consumption. I am using an MX25R64 external flash...
Hi
In my ble repeater application on nRF52833, when I adding OTA function , I found the my image rom size too large to adding FOTA with MCUBoot. there is my memory report...
Hi,
I am currently implementing an E-Ink display application using the SPI interface on our custom nRF54L15 board. I initially configured the display with the following...
Hi All,
I'm currently working with a custom board using the NPM1300 and STM32L4, alongside the npmx drivers. I'm trying to capture both pressed and released events from...
Hi, I'm currently in architecture definition stage, and I'd like to know more about the possibilities driven by Channel Sounding. From what I understand, you can only perform...
Hi,
I have two nearly identical revisions of a board with an nrf5340 which behave differently in a curious way:
On one revision I can issue a "mon reset" command in...