the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
I have several hardware pieces based on the Fanstel WM02C nRF7002 module (nRF54L15 host) and am having problems connecting to WiFi networks on a subset.
All modules successfully...
Hi -
I'd like to set the i2c to clock in at no more than 2 khz. Are there FREQUENCY register settings that would work for this. In addition, is there a reference as to how...
Hi everyone,
I'm facing an issue where MCUboot doesn't perform a swap after reboot, even though the DFU download to slot 1 completes successfully and boot_request_upgrade...
Dear team, in my design I'm using MCUBOOT to perform FOTA DFU over BLE and I need some confirmation about the building process to be sure to do all the step in a properly...
Hello, I am a beginner to nRF54 series (currently have nRF54L15DK) and to understand the concepts and communication between nRF devices and iOS software with bluetooth LE...
Title
nRF5340 DK × 2 + MCP2515/TJA1050 – can_start() = -5 (CANCTRL/CANSTAT = 0xFF). What am I missing?
Hi everyone,
I’m trying to bring-up a very small CAN bus test...
Hi,
I am working on ncs 2.9.1 @ nRF54L15.
I followed this academy course to add a single channel saadc in simple mode:
ADC read works properly, but the current read...
I would like to implement ble mesh direct forwarding feature in my code but i am not finding zephyr library for that. Is there any possibility to get link for zephyr direct...
Hi everyone,
I'm developing a Matter device on the nRF54L15 platform using NCS 2.9.0. When commissioning the device via HomePod and iPhone, the device unexpectedly reboots...
After full update modem firmware and reboot, i got this error:
E: Modem library init error: -116, lte_lc not initialized
The only way to work around is power cycle.Po...
hello Nordic
i am working with nre52840 and nrf52832, with ncs v2.8.0
i am using ble SMP service for transferring data with a central device and for DFU.
currently i...
Hlo
I have designed a custom board based on nRF5340. Now I am trying to do flashing and RF testing of it through nRF5340 development board but can't even flash it because...
Hi,
am working on nrf52840 withst7789v custom display . I have integrated the my display code using lvgl library with PMIC code in zephyr . while doing that I have configure...
Dear,
I’m experiencing an issue with performing DFU over BLE Mesh. I have a setup with one node acting as provisioner and distributor. This node has a new image loaded ...
hi support team,
i am testing SLM demo.
i found that COEX0 pin is working abnormal after about 2 minutes. may i ask why? COEX0 pin is low after 2 minutes.
the log is...
