As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi.
For a while I have had some issues with the toolchain when using the nRF connect SDK in visual studio code on windows 10. I believe it was after installing SDK version...
Hello,
I recently acquired a Thingy91 board in order to make a hardware prototype. I already have experience developing with the nRF52840 so I took inspiration from my working...
Hi,
I am trying to integrate the nRF5340 Audio application (CIS Unicast Server role with bidirectional streaming enabled) from NCS 2.9.0 into on my custom nRF5340 based...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
Hey, I am working with the Matter light bulb sample from the 2.9.1 SDK, which I have modified to support the occupancy cluster. (nRF-52840 and nRF-52840DK)
This worked fine...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
The VSCode nRF Kconfig extension has very high cpu usage (2 cores at 100%)
When disabling the extension, the cpu usage drops back to normal.
I see the following in the...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hello,
I would like to know how to build the aws_iot example without network offloading to the modem. I need to make AWS connections through both the nRF9160’s LTE-M connection...
Hi,
I am trying to program the custom nRF9160 board using SEGGER JLink/SWD programmer , For same of the boards when connected to custom board and trying to select the device...
Hello Nordic team,
I'm developing firmware for a custom board based on the nRF54L15 , where the LEDs are connected to GPIOs on port 2 . These pins do not support hardware...
