I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hey I was working on starting sample code of wifi in ncs v2.6.1. When I added the correct ssid but wrong password in the prj.conf to check the status of the connection failure...
Hi there,
I am currently trying to use device sleep modes with Matter. Nevertheless, once I add "CONFIG_PM_DEVICE_RUNTIME=y" to my prj.conf, the main-method is not longer...
Hi, I have been experimenting with the Direct Test Mode program. I am using an nRF9160 DK, specifically the bluetooth chip nRF52840.
The Direct Test Mode is not officially...
Hi,
I am using sensor observer sample to get the data from sensor sample. However, I notice the power consuption is too high. I have look thourgh the forum and found this...
Hello dear Nordic support staff,
I'm working on some legacy code (NCS 1.8.0 in case it's relevant) and see this in the inclusion list of one of the files:
Functions...
Hi,
I`m designing the schematic, and met some problems, could you please give me some guidance?
Does the pin only supports the described peripheral function and not...
Hey, I am working with the Matter light bulb sample from the 2.9.1 SDK, which I have modified to support the occupancy cluster. (nRF-52840 and nRF-52840DK)
This worked fine...
Hello, I am working with a Bluetooth Mesh network where a master node (antenna) is in charge of setting up and managing the network of nodes. This master node also deploys...
Hello,
I am currently using CADENCE for schematic design and have used Nordic's nRF9151 and nRF54L15 chips. However, the reference materials downloaded from Nordic's official...
Hello,
already found a description in the Tech Docs, how to bring the external memory into deep sleep on QSPI interface: https://docs.nordicsemi.com/bundle/ncs-latest/page...
Hello, I am following the instruction on dev academy - nrf connect sdk intermediate lesson 2 excercise 1, but I can't select data tab on memory explorer.
I can select only...
Hello support,
For our project we have an integration with Memfault for metrics, coredumps and log files.
We are currently developing in NRF 2.7.0 on a nrf9160 chip. ...
Hi,
when i try making a new connection with a new device using my for loop (reconnecting using the adresses that i stored in an array), i sometimes can get a warning which...
I'm trying to use both uart0 and uart1 on nrf5340 (only App core) but I get this message: UART_RX_BUF_REQUEST event, but not the error. I have also tried to pass another buffer...
Hi,
I am developing a demo where an nRF52840 development board measures Bluetooth RSSI simultaneously from a mobile phone and the board itself to enable computer unlocking...
