Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
running Windows 10 Pro 22H2 and using j-link v9
i tried to read firmware from nrf51822-QFAB by using " nrfjprog --readcode dump_nRF51822.hex", but it gave me an error...
I have implemented a program that sends an image's .HEX file through our custom software. The data is received and parsed by an application running on an NRF5340. The relevant...
Hi all
I am using the bluetooth central sample from zephyr. I can read the addresses of the devices but I would like to read each specific device's advertisement data. So...
I have the following settings in my prj.conf:
and getting the error
CONFIG_FLASH_MAP was assigned the value y, but got the value n. Missing dependencies: FLASH_HAS_DRIVER_ENABLED...
SDK:nRF5_SDK_17.1.0_ddde560
example: ble_app_multilink_central
softdevice: s140_nrf52_7.2.0
PCB: PCA10059 as Cental
My peripheral device's mac is 00:96:81:16:E0:9F...
Hi, I'm trying to use BLE OTA with an external memory due to my application is too big to do it only with the internal memory. When I use OTA config with internal memory,...
Since I am developing a lot for the nRF51822, I heavily relied on the old reference pages for said chip, like SDK 12.3.0 Reference .
Now they seem to be gone.
Could...
Currently nRF54L15 is being matched with LOW Q circuit and unipolar antenna. Because low Q circuit takes a lot of components and time when designing hardware. So I can remove...
We are trying to use extended BLE advertising with a nrf5340dk and are experiencing problems when trying to connect to an android phone (Android 13). Using legacy adverising...
Hello,
I noticed today that all the FOTA bundles I used to have on nRFCloud are gone !
Both the ones I added, and the "built in" ones (modem firmware).
Is this a bug...
Good Morning,
I'm currently developing an application for the nRF54L15 where I only need to send single BLE packages, therefore arising the need for keeping track of the...
Hi
I am developing an application where I need to update the BD address for advertising after each disconnection and on reboot. I know Zephyr stack has the API bt_id_reset...
I bought a tiny board on Aliexpress from HolyIOT. It comes with an nRF52832 and an LIS2DH12 accelerometer. The silkscreen on the board says HOLYIOT-21011-v1.0.
This schematic...
