Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hello,
Our company makes module using nRF52840. And we also make development kit with it.
I recently programmed open bootloader built-in hex in nRF5 SDK v17.1.0 (examples...
nrfConnectSDK V2.8
Toolchain
Board: nrf5340dk
Hi, while compiling ncs-spi-master-slave-example , I am getting below errors
In function 'spi_init': C:/Users/hello...
I am currently working on a Direction Finding project, but I am facing an issue in prj.conf .
I use an nRF52811 custom board for Direction Finding. In the board selection...
Hi,
EDITED: This appears to NOT be related to any open circuit, the SAME behavior comes even with abrupt changes to the current scale, without any interruptions. Additional...
Hi, I'm trying to install modem fw using the script given by Sigurd : https://devzone.nordicsemi.com/f/nordic-q-a/53208/updating-nrf9160-modem-firmware-through-the-command...
Hi.
code base is sdk 17.1.0
MCU : nrf52810
Softdevice : S112 (7.2.0)
use SES 5.42a
step1. modify NRF_SDH_BLE_GATT_MAX_MTU_SIZE form 23 to 50 in sdk_config.h
...
Dear nRF experts. We are a module manufacturer and we have designed an nRF45L15 module. We are doing a series of verifications. When we were doing the connection test, we...
Hi,
I use Nordic connect SDK and have to create a new revision for a custom board, because there are some hardware changes. I managed to create an overlay for the new revision...
MCUBOOT contains a flag MCUBOOT_OVERWRITE_ONLY_KEEP_BACKUP that stops it erasing a big chunk of the start of the secondary image after an update.
We would like to set this...
I'm looking for an nrfutil command to replace this command:
nrfjprog --memwr 0x10001080 --val 0x12345678
My goal is to write a serial number to the UICR CUSTOMER[0] register...
Hi All,
I have nRF54l15-PDK board which has 8MB of external flash. Currently I am exploring on basic read/write functionality on external flash.
I am using nrf sdk version...
I'm checking the function by uploading the code to the pcb that uploaded the nrf9160 chip.
I checked that the network communication is normal on the previous 9160dk board...
Hello,
I have just received the nRF5340-DK development kit. However, when I plug in the USB cable to my PC, it's not detected. I have tried multiple USB ports and the issue...
i'm working "bare-metal" with the nRF54-DK, loading from the command-line by directly calling JLink....
often (but not always) i receive the following message from JLink...
Hi there
I'm using two nRF52840 boards and I want to set them up to relay a message from one phone to another like this: phoneA > board1 > board2 > phoneB.
I have looked...
