I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
The datasheet, page 78, says "Supervisor HW to manage power on reset, brownout, and power fail".
We are powering from a solar cell, so the power supply voltage ramp will...
HI i am using nordic nrf52840 dk(pca10056) . i am using ble_app_uart example code for my development. i have connected usb in j2 but when i keep my power switch in usb adv...
Hi! I want to write some software utilizing OpenThread and CoAP. I've seen samples of coap server and coap client in NCS. However, I want to ask whether it's possible or not...
Hi,
I am currently investigating the possibility of using Nordic nRF52840 as the PAwR advertiser and the other device (from a different vendor) as the PAwR scanner. I don...
nRF 52832 + NCS 2.6.1
We are successfully setting the advertising Tx power in discrete steps {-40, -20, -16, -12, -8, -4, 0, +3, +4}dBm using
However, I am being asked...
hi support team,
customer had one problem about 9151 with esim: the iccid can't be readout, it should be 19 bytes string, but we only get 6
may i ask what could be the...
Hi
As described in this white paper: https://infocenter.nordicsemi.com/pdf/nwp_036.pdf during the reference period of CTE signals, 8 samples are taken. These samples contain...
I’m using the DECT Shell perf command to evaluate DECT NR+ performance.
Could you please clarify the units and scaling of the snr field in nrf_modem_dect_phy_rx_pcc_status...
Hi,
What file or files should contain CONFIG_GPIO=y for a simple application developed with nRF Connect SDK v2.9.0 such that VS Code does not show squiggles under #include...
Is there any point to using deferred logging with the RTT backend?
The way I understand RTT is that it writes the message to a buffer where it is fetched via DAP, skipping...
Hello,
I'm trying to implement runtime power management (SDK 2.9.0), but as soon as I enable the option, the shell and logging on UART0 stop working at startup. The rest...
Today I bought a new NRF-PPK2, but compare with my old NRF-PPK2.
For the old and new PPK2, I use the same DUT.
It can't show the same current with my old one? can you...
Hello, We are developing an application with nRF52810 based on nRF Connect SDK V2.4.1. The application is utilizing the BLE connection, particularly the NUS Service (emulation...
Hi,
In our project, we are planning to use the nRF9160 for both LTE-M and Wi-Fi. Thus, we have connected the nRF9160-DK to the nRF7002-EK in the developing phase as we read...
Greetings developers,
I am using nrf connect sdk 2.7.0 with nrf52811 soc. 1) present situation:
My application sequential in nature and does not have multiple thread...
